Toyota Camry (XV70): Disassembly
DISASSEMBLY
PROCEDURE
1. REMOVE FRONT DIFFERENTIAL CASE REAR TAPERED ROLLER BEARING (OUTER RACE)
(a) Using SST, remove the front differential case rear tapered roller bearing (outer race) from the automatic transaxle case sub-assembly.
SST: 09308-36010
NOTICE:
Be careful not to damage the automatic transaxle case sub-assembly.
HINT:
Align the claw of the SST with the indentation of the automatic transaxle case sub-assembly when removing the parts.
2. REMOVE FRONT DIFFERENTIAL CASE REAR TAPERED ROLLER BEARING (INNER RACE)
| (a) Using SST, remove the front differential case rear tapered roller bearing (inner race) from the differential case assembly. SST: 09950-40011 09951-04010 09952-04010 09953-04030 09954-04020 09955-04011 09957-04010 09958-04011 SST: 09950-60011 09951-00340 09951-00440 09952-06010 NOTICE: Because SST is attached to the roller portion, there is a possibility that the roller portion could break and SST could come off before the front differential case rear tapered roller bearing (inner race) comes off. |
|
| (b) If the roller portion breaks and SST comes off, reattach SST to the inner race in the position shown in the illustration, and continue removing the parts. SST: 09950-40011 09951-04010 09952-04010 09953-04030 09954-04020 09955-04011 09957-04010 09958-04011 SST: 09950-60011 09951-00340 09951-00440 09952-06010 |
|
3. REMOVE FRONT DIFFERENTIAL CASE FRONT TAPERED ROLLER BEARING (OUTER RACE)
(a) Using SST, remove the front differential case front tapered roller bearing (outer race) and differential drive pinion shim from the transaxle housing.
SST: 09308-36010
NOTICE:
Be careful not to damage the transaxle housing.
HINT:
Align the claw of the SST with the indentation of the transaxle housing when removing the parts.
4. REMOVE FRONT DIFFERENTIAL CASE FRONT TAPERED ROLLER BEARING (INNER RACE)
| (a) Using SST, remove the front differential case front tapered roller bearing (inner race) from the differential case assembly. SST: 09950-00020 SST: 09950-00030 SST: 09950-60011 09951-00440 |
|
READ NEXT:
Inspection
INSPECTION PROCEDURE 1. INSPECT DIFFERENTIAL CASE ASSEMBLY
(a) Using SST, rotate the front differential side gear as shown in the illustration.
SST: 09528-52010 09528-05030 Standard: The fro
Reassembly
REASSEMBLY PROCEDURE 1. INSTALL FRONT DIFFERENTIAL CASE FRONT TAPERED ROLLER BEARING (INNER RACE)
(a) Using SST and a press, install a new front differential case front tapered roller bearing (i
Differential Oil Seal
ComponentsCOMPONENTS ILLUSTRATION
*1 DRIVE SHAFT BEARING BRACKET
*2 FRONT DRIVE SHAFT OIL SEAL LH
*3 FRONT DRIVE SHAFT OIL SEAL RH
- -
N*m (kgf*cm,
SEE MORE:
Internal Control Module EEPROM Data Memory Failure (P062F44)
DESCRIPTION The ECM monitors its internal operation and will store this DTC when it detects an internal malfunction.
DTC No. Detection Item
DTC Detection Condition Trouble Area
MIL Memory
Note P062F44
Internal Control Module EEPROM Data Memory Failure
ECM i
Radio Broadcast cannot be Received or Poor Reception
CAUTION / NOTICE / HINT
NOTICE:
Depending on the parts that are replaced during vehicle inspection or maintenance, performing initialization, registration or calibration may be needed. Refer to Precaution for Navigation System.
Click here
When replacing the radio and display receiver
