Toyota Camry (XV70): VSC does not Operate or VSC does not Operate Correctly
DESCRIPTION
When TRAC or VSC is operating, the skid control ECU (brake actuator assembly) blinks the slip indicator light to inform the driver that slippage occurred.
When a communication malfunction with the ECM is detected, TRAC and VSC are disabled. Also, TRAC and VSC are disabled when a DTC is stored.
When in VSC off mode, or TRAC and VSC are disabled, the multi-information display in the combination meter assembly displays "Traction Control Turned Off" and the VSC OFF indicator light illuminates to inform the driver.
CAUTION / NOTICE / HINT
NOTICE:
After replacing or reinstalling the yaw rate and acceleration sensor (airbag sensor assembly), perform acceleration sensor zero point calibration and system information memorization after performing "Reset Memory".
Click here .gif)
PROCEDURE
| 1. |
BRAKE PROBLEM CHECK |
(a) Check whether the slip indicator light was illuminated when VSC did not operate.
OK:
The slip indicator light was illuminated.
HINT:
When a DTC is stored, the slip indicator light is illuminated and VSC does not operate due to the fail-safe function.
(b) Check whether the vehicle speed was 15 km/h (9 mph) or less when VSC did not operate.
OK:
The vehicle speed was 15 km/h (9 mph) or less.
HINT:
VSC does not operate when the vehicle speed is 15 km/h (9 mph) or less.
(c) Check whether the vehicle was driven straight for a few seconds at 15 km/h (9 mph) or more.
OK:
The vehicle was not driven straight for a few seconds at 15 km/h (9 mph) or more.
HINT:
When the ignition switch is turned to ON, as steering angle sensor zero point calibration is not performed below 15 km/h (9 mph), VSC will not operate until the vehicle is driven straight for a few seconds at 15 km/h (9 mph) or more.
| OK | .gif) | END |
|
.gif)
| 2. |
CHECK DTC |
(a) Connect the Techstream to the DLC3.
(b) Turn the ignition switch to ON.
(c) Enter the following menus: Chassis / Brake/EPB / Trouble Codes.
(d) Check the DTCs (vehicle stability control system) that are output.
Chassis > Brake > Trouble Codes| Result |
Proceed to |
|---|---|
| DTCs are not output |
A |
| Vehicle stability control system DTCs are output |
B |
| B |
| REPAIR CIRCUITS INDICATED BY OUTPUT DTCS
|
|
| 3. |
CHECK TIRES |
(a) Check that the tire of each wheel is the correct size.
Click here
OK:
The tire of each wheel is the correct size.
| NG | | REPLACE THE TIRE OF EACH WHEEL WITH THE CORRECT SIZE |
|
| 4. |
CHECK AIRBAG SENSOR ASSEMBLY INSTALLATION |
(a) Check that the yaw rate and acceleration sensor (airbag sensor assembly) has been installed properly.
Click here
OK:
The yaw rate and acceleration sensor (airbag sensor assembly) is tightened to the specified torque.
The yaw rate and acceleration sensor (airbag sensor assembly) is not installed in a tilted position.
| OK | | PERFORM OBTAIN ACCELERATION SENSOR ZERO POINT
|
| NG | | INSTALL AIRBAG SENSOR ASSEMBLY CORRECTLY |
READ NEXT:
Brake Actuator Operation Sound is Loud during Initial Check
CAUTION / NOTICE / HINT NOTICE: After replacing the skid control ECU (brake actuator assembly), perform acceleration sensor zero point calibration and system information memorization.
Click here
VSC OFF Switch Circuit
DESCRIPTION The skid control ECU (brake actuator assembly) is connected to the combination meter assembly via CAN communication.
Pressing the VSC OFF switch turns off TRAC operation, and pressing an
SEE MORE:
Data List / Active Test
DATA LIST / ACTIVE TEST NOTICE: In the table below, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.
HINT: Using the Techstream to read the Data List allows the values or states of switche
Torque Converter And Drive Plate
InspectionINSPECTION PROCEDURE
1. INSPECT TORQUE CONVERTER ASSEMBLY (a) Inspect the one-way clutch. Press on the splines of the stator with a finger and rotate it. Check that it rotates smoothly when turned clockwise and rotates with difficulty when turned counterclockwise.
Diffic
