Toyota Camry owners & service manuals

Toyota Camry (XV70): Automatic door locking and unlocking systems

The following functions can be set or cancelled:

Opening, closing and locking the doors

■Switching the door unlock function (vehicles with a smart key system)

It is possible to set which doors the entry function unlocks using the wireless remote control.

1. Turn the engine switch off.

2. When the indicator light on the key surface is not on, press and hold , or for approximately 5 seconds while pressing and holding .

The setting changes each time an operation is performed, as shown below.

(When changing the setting continuously, release the buttons, wait for at least 5 seconds, and repeat step 2.)

Opening, closing and locking the doors

*1: 4.2-inch display
*2: 7-inch display

To prevent unintended triggering of the alarm, unlock the doors using the wireless remote control and open and close a door once after the settings have been changed. (If a door is not opened within 60 seconds after is pressed, the doors will be locked again and the alarm will automatically be set.) In case that the alarm is triggered, immediately stop the alarm.

■Impact detection door lock release system

In the event that the vehicle is subject to a strong impact, all the doors are unlocked. Depending on the force of the impact or the type of accident, however, the system may not operate.

■Open door warning buzzer

If the vehicle reaches a speed of 3 mph (5 km/h), the master warning light flashes and a buzzer sounds to indicate that the door(s) are not yet fully closed.

The open door(s) is displayed on the multi-information display.

■Conditions affecting the operation of the smart key system or wireless remote control

Vehicles without a smart key system

Vehicles with a smart key system

■Rear seat reminder function

In order to remind you not to forget luggage, etc. in the rear seat, when the engine switch is turned off after any of the following conditions are met, a buzzer will sound and a message will be displayed on the multi-information display for approximately 6 seconds.

  • The engine is started within 10 minutes after opening and closing a rear door.
  • A rear door has been opened and closed after the engine was started.

However, if a rear door is opened and then closed within approximately 2 seconds, the rear seat reminder function may not operate.

The rear seat reminder function determines that luggage, etc. has been placed in a rear seat based on opening and closing of a rear door. Therefore, depending on the situation, the rear seat reminder function may not operate and you may still forget luggage, etc. in the rear seat, or it may operate unnecessarily.

The rear seat reminder function can be enabled/disabled.

■Customization

Some functions can be customized.

WARNING

■To prevent an accident

Observe the following precautions while driving the vehicle.

Failure to do so may result in a door opening and an occupant falling out, resulting in death or serious injury.

  • Ensure that all doors are properly closed.
  • Do not pull the inside handle of the doors while driving.

    Be especially careful for the front doors, as the doors may be opened even if the inside lock buttons are in locked position.

  • Set the rear door child-protector locks when children are seated in the rear seats.

■When opening or closing a door

Check the surroundings of the vehicle such as whether the vehicle is on an incline, whether there is enough space for a door to open and whether a strong wind is blowing.

When opening or closing the door, hold the door handle tightly to prepare for any unpredictable movement.

    READ NEXT:

     Trunk

    The trunk can be opened using the trunk opener switch, entry function (vehicles with a smart key system), wireless remote control or key. Opening the trunk from inside the vehicle Press and hold t

     Smart key system

    The following operations can be performed simply by carrying the electronic key on your person, for example in your pocket. (The driver should always carry the electronic key.) Locks and unloc

     Adjusting the seats

    SEE MORE:

     Fail-safe Chart

    FAIL-SAFE CHART Description The fail-safe function minimizes the loss of operation when a malfunction occurs in a sensor or solenoid. Fail-safe (a) Fail-safe control list: Malfunctioning Part Function Transmission Revolution Sensor (NT) Lock up clutch control is prohibit

     Installation

    INSTALLATION PROCEDURE 1. INSTALL CAMSHAFT TIMING GEAR BOLT (a) Make sure that the No. 1 cylinder is at TDC/compression. HINT: Check that the cutout of the camshaft timing gear assembly is at the top and align the timing mark (cutout) of the crankshaft pulley with the timing mark on the timing c

    © 2023-2024 Copyright www.tocamry.com