Toyota Camry (XV70): Dtc Check / Clear
DTC CHECK / CLEAR
DTC CHECK
(a) Turn the ignition switch off.
(b) Connect the Techstream to the DLC3.
(c) Turn the ignition switch to ON.
(d) Turn the Techstream on.
(e) Read the DTCs following the prompts on the Techstream. Enter the following menus: Chassis / Brake / Trouble Codes.
Chassis > Brake > Trouble Codes(f) Check the details of the DTCs.
NOTICE:
Make sure to clear the DTCs after repair.
|
Display Item | Description |
|---|---|
|
Test Failed | Shows the malfunction judgment results during the current trip. |
|
Confirmed | Shows the DTCs confirmed up to now (The number of current trips differs for each DTC.) |
- Freeze frame data is stored for each of the latest result DTCs and confirmed DTCs.
- Refer to the diagnostic trouble code chart and perform the necessary troubleshooting procedures.
Click here
.gif)
(g) Check the freeze frame data.
(1) If a DTC is stored, check the corresponding freeze frame data to gain an understanding of the vehicle condition at the time.
Click here
CHECK TIME STAMP
HINT:
By checking Time Stamp, the time and order in which DTCs were stored in an ECU can be checked.
(a) Turn the ignition switch off.
(b) Connect the Techstream to the DLC3.
(c) Turn the ignition switch to ON.
(d) Turn the Techstream on.
(e) Enter the following menus: Health Check.
(f) Perform the following steps when the data setting screen is displayed.
(g) Select the systems for which to perform Health Check and check for time stamp data.
Selectable items:- Powertrain
- Chassis
- Body
- Store All Data
(h) Select "Yes" when "Would you like to include Time Stamp Data?" is displayed.
HINT:
If "Yes" is not selected, time stamp data will not be stored.
(i) After Health Check has completed, select "Time Stamp Data" to display the Time Stamp screen.
(j) Select the desired system from the drop-down list on the bottom of the Time Stamp screen.
(k) Check the order and time which DTCs were stored for the selected system.
DTC CLEAR
(a) Turn the ignition switch off.
(b) Connect the Techstream to the DLC3.
(c) Turn the ignition switch to ON.
(d) Turn the Techstream on.
(e) Operate the Techstream to clear the codes. Enter the following menus: Chassis / Brake / Trouble Codes.
Chassis > Brake > Clear DTCs(f) Press the DTC clear button.
NOTICE:
When DTCs are cleared, all data related to the DTCs is also cleared.
HINT:
If the malfunction continues, the DTCs will be stored again when the detection conditions are met.
READ NEXT:
Freeze Frame Data
FREEZE FRAME DATA FREEZE FRAME DATA/INFORMATION
(a) Using the Techstream, check the vehicle condition (ECU, sensor) when the brake system operates or a DTC is output.
CHECK FREEZE FRAME DATA AND I
Fail-safe Chart
FAIL-SAFE CHART FAIL-SAFE CHART (a) When the skid control ECU (brake actuator assembly) detects a solenoid valve malfunction or abnormal signal from a sensor, the brake actuator assembly cuts power an
Data List / Active Test
DATA LIST / ACTIVE TEST DATA LIST NOTICE:
In the table below, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a
SEE MORE:
Open in Outer Mirror Indicator(Slave) (C1AB5)
DESCRIPTION This DTC is stored when the blind spot monitor sensor LH detects an open in the outer rear view mirror indicator LH.
DTC No. Detection Item
DTC Detection Condition Trouble Area
C1AB5 Open in Outer Mirror Indicator(Slave) Both of the following conditions are met
General Information
GENERAL INFORMATION
A large number of ECU controlled systems are used in this vehicle. In general, ECU controlled systems are considered to be very intricate, requiring a high level of technical knowledge to troubleshoot. However, most problem checking procedures only involve inspecting the ECU
