Toyota Camry (XV70): Multi-axis Acceleration Sensor Module "A" Missing Calibration (C051D54)
DESCRIPTION
The airbag sensor assembly has a built-in yaw rate and acceleration sensor and detects the vehicle condition.
The skid control ECU (brake actuator assembly) receives signals from the yaw rate and acceleration sensor (airbag sensor assembly) via CAN communication.
HINT:
If a communication error with the yaw rate and acceleration sensor (airbag sensor assembly) is detected, DTCs U012587 and U015187 are stored.
The DTC is also stored when the calibration has not been completed.
|
DTC No. | Detection Item |
DTC Detection Condition | Trouble Area |
|---|---|---|---|
|
C051D54 | Multi-axis Acceleration Sensor Module "A" Missing Calibration |
Zero point calibration of acceleration sensor undone. |
|
CAUTION / NOTICE / HINT
NOTICE:
- After replacing the skid control ECU (brake actuator assembly), perform acceleration sensor zero point calibration and system information memorization.
Click here
.gif)
- After replacing or reinstalling the yaw rate and acceleration sensor (airbag sensor assembly), perform acceleration sensor zero point calibration and system information memorization after performing "Reset Memory".
Click here
PROCEDURE
|
1. | PERFORM ACCELERATION SENSOR ZERO POINT CALIBRATION |
(a) Connect the Techstream to the DLC3.
(b) Turn the ignition switch to ON.
(c) Enter the following menus: Chassis / Brake/EPB / Utility / Reset Memory.
(d) Clear the zero point calibration data and system information.
Click here
|
Tester Display |
|---|
| Reset Memory |
(e) Perform acceleration sensor zero point calibration and system information memorization.
Click here
|
Tester Display |
|---|
| Calibration |
|
.gif)
| 2. |
RECONFIRM DTC |
(a) Connect the Techstream to the DLC3.
(b) Turn the ignition switch to ON.
(c) Operate the Techstream to clear the codes. Enter the following menus: Chassis / Brake/EPB / Trouble Codes.
Chassis > Brake > Clear DTCs(d) Press the DTC clear button.
(e) Turn the ignition switch off.
(f) Turn the ignition switch to ON.
(g) Read the DTCs following the prompts on the Techstream. Enter the following menus: Chassis / Brake/EPB / Trouble Codes.
Chassis > Brake > Trouble Codes(h) Check if the same DTC is output.
|
Result | Proceed to |
|---|---|
|
C051D54 is not output |
A |
| C051D54 is output |
B |
| A |
.gif) | END |
|
| 3. |
CHECK AIRBAG SENSOR ASSEMBLY INSTALLATION |
(a) Check that the yaw rate and acceleration sensor (airbag sensor assembly) has been installed properly.
Click here
OK:
The yaw rate and acceleration sensor (airbag sensor assembly) is tightened to the specified torque.
The yaw rate and acceleration sensor (airbag sensor assembly) is not installed in a tilted position.
| NG | | INSTALL AIRBAG SENSOR ASSEMBLY CORRECTLY |
|
| 4. |
READ VALUE USING TECHSTREAM (LATERAL G AND FORWARD AND REARWARD G) |
(a) Connect the Techstream to the DLC3.
(b) Turn the ignition switch to ON.
(c) Enter the following menus: Chassis / Brake/EPB / Data List.
Chassis > Brake > Data List|
Tester Display | Measurement Item |
Range | Normal Condition |
Diagnostic Note |
|---|---|---|---|---|
|
Lateral G | Lateral G |
Min.: -25.105 m/s2, Max.: 24.908 m/s2 |
Turning right: -25.105 to 0.000 m/s2 Turning left: 0.000 to 24.908 m/s2 |
During turning: Changes in proportion with lateral acceleration |
|
Forward and Rearward G |
Forward and rearward G |
Min.: -25.105 m/s2, Max.: 24.908 m/s2 |
During deceleration: -25.105 to 0.000 m/s2 During acceleration: 0.000 to 24.908 m/s2 |
During acceleration/deceleration: Changes in proportion with acceleration |
|
Tester Display |
|---|
| Lateral G |
|
Forward and Rearward G |
(d) Check the acceleration sensor (airbag sensor assembly) output value displayed on the Techstream.
OK:
The acceleration sensor (airbag sensor assembly) output value is normal.
| OK | | REPLACE BRAKE ACTUATOR ASSEMBLY |
| NG | | REPLACE AIRBAG SENSOR ASSEMBLY |
READ NEXT:
Multi-axis Acceleration Sensor Module "A" Circuit Voltage Out of Range (C05201C)
DESCRIPTION The airbag sensor assembly has a built-in yaw rate and acceleration sensor and detects the vehicle condition.
When the skid control ECU (brake actuator assembly) detects an abnormal acce
Multi-axis Acceleration Sensor Module "A" Circuit Voltage Out of Range (C05201C)
DESCRIPTION The airbag sensor assembly has a built-in yaw rate and acceleration sensor and detects the vehicle condition.
When the skid control ECU (brake actuator assembly) detects an abnormal acce
Multi-axis Acceleration Sensor Module "A" Signal Stuck In Range (C05202A)
DESCRIPTION The airbag sensor assembly has a built-in yaw rate and acceleration sensor and detects the vehicle condition.
The skid control ECU (brake actuator assembly) memorizes the range of the ac
SEE MORE:
Installation
INSTALLATION PROCEDURE 1. INSTALL V-RIBBED BELT
HINT: When reusing the V-ribbed belt, check the ribs and back of the V-ribbed belt for wear and cracks. If wear or a crack that reaches the core (at more than 1 point) is found, replace the V-ribbed belt.
(a) Set the V-ribbed belt onto each pul
Left Front Wheel Speed Sensor Internal Electronic Failure (C050049)
DESCRIPTION When the system is starting up and the skid control ECU (brake actuator assembly) detects a speed sensor circuit malfunction via the speed sensor circuit self-diagnosis function, this DTC is stored.
DTC No. Detection Item
DTC Detection Condition Trouble Area
C05004
