Toyota Camry (XV70): Pressure Control Solenoid "G" Circuit Short to Battery (P280712)

DESCRIPTION

Changing gears is performed by the ECM turning the solenoid (SL1, SL2, SL3, SL4, SL5 and SL6) valves on and off.

If an open or short occurs in any of the solenoid valve circuits, the ECM controls the remaining normal solenoid valves to allow the vehicle to be driven. If all of the solenoid valves are malfunctioning, only the mechanical fluid pressure circuit will function and some manual operation will be possible. If an open or short occurs in a solenoid valve circuit, the ECM cuts power to the malfunctioning solenoid valve.

HINT:

The following table shows normal operation of the solenoid (SL4) valve when the shift lever is in D.

MONITOR DESCRIPTION

This DTC indicates a short to +B in the solenoid (SL4) valve circuit. The ECM commands gear shifts by turning the solenoid valves on or off. When there is an open or short in any solenoid valve circuit, the ECM detects the problem, illuminates the MIL and stores a DTC.

The ECM performs the fail-safe function and turns the other normal solenoid valves on or off. In the case of an open or short circuit, the ECM stops sending current to the open or shorted solenoid.

MONITOR STRATEGY

TYPICAL ENABLING CONDITIONS

TYPICAL MALFUNCTION THRESHOLDS

Any of the following conditions are met: Condition (A) or (B)

COMPONENT OPERATING RANGE

Both of the following conditions are met: Condition (A) and (B)

CONFIRMATION DRIVING PATTERN

CAUTION:

When performing the confirmation driving pattern, obey all speed limits and traffic laws.

HINT:

• After repairs have been completed, clear the DTCs and then check that the vehicle has returned to normal by performing the following All Readiness check procedure.
• When clearing the permanent DTCs, refer to the Clear Permanent DTC procedure.

  Click here

1. Connect the Techstream to the DLC3.
2. Turn the engine switch on (IG) and turn the Techstream on.
3. Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).
4. Turn the engine switch off and wait for 2 minutes or more.
5. Turn the engine switch on (IG) and turn the Techstream on.
6. Start the engine.
7. Perform the D Position Shift Test inspection in Road Test. [*1]

   Click here

   HINT:

   [*1] : Normal judgment procedure.

   The normal judgment procedure is used to complete DTC judgment and also used when clearing permanent DTCs.

8. Stop the vehicle.
9. Enter the following menus: Powertrain / Transmission / Utility / All Readiness.
10. Input the DTC: P280712.
11. Check the DTC judgment result.

    Techstream Display	Description
    NORMAL	DTC judgment completed System normal
    ABNORMAL	DTC judgment completed System abnormal
    INCOMPLETE	DTC judgment not completed Perform driving pattern after confirming DTC enabling conditions
    N/A	Unable to perform DTC judgment Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit

    HINT:

    • If the judgment result shows NORMAL, the system is normal.
    • If the judgment result shows ABNORMAL, the system has a malfunction.
    • If the judgment result shows INCOMPLETE or N/A, perform the normal judgment procedure again.

WIRING DIAGRAM

CAUTION / NOTICE / HINT

NOTICE:

• Perform the universal trip to clear permanent DTCs.

  Click here

• Perform registration and/or initialization when parts related to the automatic transaxle are replaced.

  Click here

PROCEDURE

(a) Disconnect the C96 ECM connector.

(b) Measure the resistance according to the value(s) in the table below.

Standard Resistance:

NG

GO TO STEP 3

OK

(a) Replace the ECM.

Click here

NEXT

PERFORM REGISTRATION

(a) Disconnect the C92 transmission wire connector.

(b) Disconnect the C96 ECM connector.

(c) Measure the resistance according to the value(s) in the table below.

Standard Resistance:

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (TRANSMISSION WIRE - ECM)

OK

(a) Remove the solenoid (SL4) valve. Click here

*a Component without harness connected (Solenoid (SL4) Valve)

(b) Measure the resistance according to the value(s) in the table below.

Standard Resistance:

READ NEXT: