Toyota Camry (XV70): Rear Axle Hub Bolt(w/ Electric Parking Brake System)
Components
COMPONENTS
ILLUSTRATION
|
*1 | NO. 2 PARKING BRAKE WIRE ASSEMBLY |
*2 | REAR AXLE HUB BOLT |
|
*3 | REAR DISC |
*4 | REAR DISC BRAKE CALIPER ASSEMBLY |
|
*5 | REAR FLEXIBLE HOSE |
- | - |
.png) |
Tightening torque for "Major areas involving basic vehicle performance such as moving/turning/stopping": N*m (kgf*cm, ft.*lbf) |
● | Non-reusable part |
Replacement
REPLACEMENT
CAUTION / NOTICE / HINT
HINT:
- Use the same procedure for the RH side and LH side.
- The following procedure is for the LH side.
PROCEDURE
1. REMOVE REAR WHEEL
Click here
.gif)
2. DISCONNECT NO. 2 PARKING BRAKE WIRE ASSEMBLY
Click here
3. SEPARATE REAR DISC BRAKE CALIPER ASSEMBLY
(a) Remove the 2 bolts and separate the rear disc brake caliper assembly from the rear axle carrier sub-assembly.
NOTICE:
Use wire or an equivalent tool to keep the rear disc brake caliper assembly from hanging by the rear flexible hose.
4. REMOVE REAR DISC
Click here
5. REMOVE REAR AXLE HUB BOLT
| (a) Temporarily install 2 service nuts to the rear axle hub bolts as shown in the illustration. Recommended Service Nut: Thread diameter: 12.0 mm (0.472 in.) Thread pitch: 1.5 mm (0.0591 in.) NOTICE: Install the service nuts to prevent damage to the rear axle hub bolts. |
|
(b) Using SST and a screwdriver or an equivalent tool to hold the rear axle hub and bearing assembly, remove the rear axle hub bolt.
SST: 09628-10011
NOTICE:
Do not damage the threads of the rear axle hub bolts.
6. INSTALL REAR AXLE HUB BOLT
| (a) Temporarily install a new rear axle hub bolt to the rear axle hub and bearing assembly. |
|
(b) Install a washer and service nut to the rear axle hub bolt as shown in the illustration.
Recommended Service Nut:
Thread diameter: 12.0 mm (0.472 in.)
Thread pitch: 1.5 mm (0.0591 in.)
HINT:
Recommended washer thickness is 5 mm (0.197 in.) or more.
(c) Using a screwdriver or an equivalent tool to hold the rear axle hub and bearing assembly, install the rear axle hub bolt by tightening the service nut.
NOTICE:
- Install the service nuts to prevent damage to the rear axle hub bolts.
- Do not damage the threads of the rear axle hub bolts.
(d) Remove the 3 service nuts and washer from the 3 rear axle hub bolts.
7. INSTALL REAR DISC
Click here
8. INSTALL REAR DISC BRAKE CALIPER ASSEMBLY
(a) Install the rear disc brake caliper assembly to the rear axle carrier sub-assembly with the 2 bolts.
Torque:
107 N
READ NEXT:
Rear Axle Hub Bolt(w/o Electric Parking Brake System)
ComponentsCOMPONENTS ILLUSTRATION
*1 PARKING BRAKE SHOE ADJUSTING HOLE PLUG
*2 REAR AXLE HUB BOLT
*3 REAR DISC
*4 REAR DISC BRAKE CALIPER ASSEMBLY
*5 RE
Components
COMPONENTS ILLUSTRATION
*1 REAR DIFFERENTIAL CARRIER ASSEMBLY
*2 WIRE HARNESS CLAMP BRACKET
*3 REAR UPPER DIFFERENTIAL MOUNT STOPPER
*4 REAR LOWER DIFFERENTIAL MO
SEE MORE:
Buzzer does not Sound
WIRING DIAGRAM
CAUTION / NOTICE / HINT
NOTICE:
When checking for DTCs, make sure that the blind spot monitor system is turned on.
Inspect the fuses for circuits related to this system before performing the following procedure.
PROCEDURE
1. CHECK RCTA BUZZER (BLIND SPOT MO
Freeze Frame Data
FREEZE FRAME DATA FREEZE FRAME DATA/INFORMATION
(a) Using the Techstream, check the vehicle condition (ECU, sensor) when the brake system operates or a DTC is output.
CHECK FREEZE FRAME DATA AND INFORMATION WHEN DTC WAS STORED (a) Freeze Frame Data is stored when a DTC is output.
(b) Once Free
