Toyota Camry (XV70): Removal
REMOVAL
CAUTION / NOTICE / HINT
The necessary procedures (adjustment, calibration, initialization or registration) that must be performed after parts are removed and installed, or replaced during radiator assembly removal/installation are shown below.
Necessary Procedures After Parts Removed/Installed/Replaced|
Replaced Part or Performed Procedure |
Necessary Procedure | Effect/Inoperative Function when Necessary Procedure not Performed |
Link |
|---|---|---|---|
| Front bumper assembly (w/ Panoramic view monitor system) |
Front television camera view adjustment |
Panoramic view monitor system |
|
PROCEDURE
1. REMOVE FRONT WHEEL OPENING EXTENSION PAD RH
Click here
.gif)
2. REMOVE FRONT WHEEL OPENING EXTENSION PAD LH
Click here
3. REMOVE REAR ENGINE UNDER COVER LH
Click here
4. REMOVE REAR ENGINE UNDER COVER RH
Click here
5. REMOVE NO. 1 ENGINE UNDER COVER
Click here
6. DRAIN ENGINE COOLANT
Click here
7. REMOVE HEADLIGHT ASSEMBLY
Click here
8. REMOVE THERMISTOR ASSEMBLY
Click here
9. REMOVE NO. 2 FRONT BUMPER ENERGY ABSORBER
Click here
10. REMOVE FRONT BUMPER ENERGY ABSORBER
Click here
11. REMOVE FRONT BUMPER REINFORCEMENT
Click here
12. REMOVE HOOD LOCK ASSEMBLY
Click here
13. REMOVE INLET AIR CLEANER ASSEMBLY
Click here
14. REMOVE UPPER RADIATOR MOUNTING BRACKET
| (a) Disconnect the 2 horn connectors. |
|
| (b) Remove the 2 bolts, 2 nuts and 2 upper radiator mounting brackets. |
|
15. REMOVE NO. 1 RADIATOR AIR GUIDE LH
| (a) Remove the clip and disengage the claw. |
|
(b) Disengage the guide to remove the No. 1 radiator air guide LH with the front radiator side air guide plate LH.
16. REMOVE NO. 1 RADIATOR AIR GUIDE RH
| (a) Remove the clip and disengage the claw. |
|
(b) Disengage the guide to remove the No. 1 radiator air guide RH.
17. REMOVE UPPER RADIATOR SUPPORT SUB-ASSEMBLY
| (a) Disengage the clamp to disconnect the hood lock control cable assembly from the upper radiator support sub-assembly. |
|
| (b) Remove the 4 bolts and upper radiator support sub-assembly. |
|
18. DISCONNECT NO. 5 WATER BY-PASS HOSE
| (a) Disengage the 4 clamps to disconnect the No. 5 water by-pass hose and No. 6 water by-pass hose from the hose clamp (A). |
|
(b) Disengage the 2 clamps to remove the hose clamp (B) from the No. 5 water by-pass hose and No. 6 water by-pass hose.
| (c) Slide the clip and disconnect the No. 5 water by-pass hose from the radiator assembly. |
|
19. DISCONNECT NO. 1 RADIATOR HOSE
| (a) Disengage the clamp and disconnect the No. 1 radiator hose from the fan shroud assembly. |
|
(b) Slide the clip and disconnect the No. 1 radiator hose from the radiator assembly.
20. DISCONNECT NO. 2 RADIATOR HOSE
| (a) Slide the clip and disconnect the No. 2 radiator hose from the radiator assembly. |
|
21. REMOVE RADIATOR ASSEMBLY
| (a) Disengage the 2 claws. |
|
(b) Disengage the 2 guides to separate the cooler condenser assembly from the radiator assembly.
NOTICE:
Make sure not to damage the cooler condenser assembly when separating the cooler condenser assembly.
(c) Disconnect the cooling fan motor connector.
| (1) Disengage the claw and raise the lock lever to disconnect the cooling fan motor connector as shown in the illustration. NOTICE: After disconnecting the cooling fan motor connector, make sure that dirt, water or other foreign matter does not contact the connecting parts of the cooling fan motor connector. |
|
.png)
(2) Disengage the wire harness clamp.
(d) Remove the radiator assembly with the fan shroud assembly from the vehicle body.
NOTICE:
Do not apply excessive force to the cooler condenser assembly or pipe when removing the radiator assembly with the fan shroud assembly.
| (e) Disengage the 2 claws. |
|
.png)
(f) Disengage the 2 guides to remove the fan shroud assembly from the radiator assembly.
NOTICE:
Do not damage the radiator assembly when removing the fan shroud assembly.
22. REMOVE RADIATOR SUPPORT CUSHION
(a) Remove the 2 radiator support cushions from the radiator assembly.
23. REMOVE LOWER RADIATOR SUPPORT
(a) Remove the 2 lower radiator supports from the radiator assembly.
READ NEXT:
Installation
INSTALLATION PROCEDURE 1. INSTALL LOWER RADIATOR SUPPORT
(a) Install the 2 lower radiator supports to the radiator assembly. 2. INSTALL RADIATOR SUPPORT CUSHION
(a) Install the 2 radiator support
Components
COMPONENTS ILLUSTRATION
*1 FRONT WHEEL OPENING EXTENSION PAD LH
*2 FRONT WHEEL OPENING EXTENSION PAD RH
*3 NO. 1 ENGINE UNDER COVER
*4 REAR ENGINE UNDER COVER LH
SEE MORE:
Mute Signal Circuit between Stereo Component Amplifier and Telematics Transceiver
DESCRIPTION The DCM (telematics transceiver) sends a mute signal to the stereo component amplifier assembly.
The stereo component amplifier assembly controls the volume according to the mute signal from the DCM (telematics transceiver). WIRING DIAGRAM
CAUTION / NOTICE / HINT
NOTICE:
Depen
Pressure Control Solenoid "B" Actuator Stuck Off (P07757F)
DESCRIPTION Based on signals from the transmission revolution sensors (NT and NC), the actual gear is detected.
The ECM compares the actual gear with the shift schedule in the ECM memory to detect mechanical malfunctions of the solenoid valves, transmission valve body assembly and automatic transa
