Toyota Camry (XV70): RR Speed Sensor Wrong Installation (X0454)
DESCRIPTION
|
Code | Tester Display |
Measurement Item | Trouble Area |
|---|---|---|---|
|
X0454 | RR Speed Sensor Wrong Installation |
History of rear speed sensor RH being installed incorrectly |
Rear Speed Sensor RH |
PROCEDURE
| 1. |
CHECK FOR DTCs (HEALTH CHECK) |
(a) Perform the Health Check using the Techstream.
| Result |
Proceed to |
|---|---|
| DTCs are not output |
A |
| DTCs are output |
B |
| B |
.gif) | GO TO DIAGNOSTIC TROUBLE CODE CHART |
|
.gif)
| 2. |
CHECK PART NUMBER (REAR SPEED SENSOR RH) |
(a) Check that the rear speed sensor RH is installed.
OK:
Proper rear speed sensor RH is installed.
NOTICE:
If it is necessary to remove components in order to check the rear speed sensor RH, follow the relevant installation and removal procedures and precautions for those components.
HINT:
The rear speed sensor RH and rear speed sensor rotor RH are incorporated into the rear axle hub and bearing assembly RH.
If the rear speed sensor RH and rear speed sensor rotor RH need to be replaced, replace the rear axle hub and bearing assembly RH.
| NG | | REPLACE REAR SPEED SENSOR RH |
|
| 3. |
CLEAR VEHICLE CONTROL HISTORY (RoB) |
(a) Using the Techstream, clear the Vehicle Control History (RoB).
Chassis > Brake > Utility|
Tester Display |
|---|
| Vehicle Control History (RoB) |
|
| 4. |
CHECK VEHICLE CONTROL HISTORY (RoB) |
(a) Using the Techstream, check for Vehicle Control History (RoB).
Chassis > Brake > Utility|
Tester Display |
|---|
| Vehicle Control History (RoB) |
HINT:
The rear speed sensor RH and rear speed sensor rotor RH are incorporated into the rear axle hub and bearing assembly RH.
If the rear speed sensor RH and rear speed sensor rotor RH need to be replaced, replace the rear axle hub and bearing assembly RH.
| Result |
Proceed to |
|---|---|
| X0454 is not output |
A |
| X0454 is output |
B |
| A |
| USE SIMULATION METHOD TO CHECK
|
.gif)
| B |
| REPLACE REAR SPEED SENSOR RH |
READ NEXT:
Yaw Rate Sensor Wrong Installation (X0456)
DESCRIPTION The airbag sensor assembly has a built-in yaw rate and acceleration sensor and detects the vehicle condition.
Code Tester Display
Measurement Item Trouble Area
X0456
Zero Point Calibration of Steering Angle Sensor Initialization Malfunction (X208A)
DESCRIPTION
Code Tester Display
Measurement Item Trouble Area
X208A Zero Point Calibration of Steering Angle Sensor Initialization Malfunction
History of failure in acqu
TRAC does not Operate
DESCRIPTION When TRAC or VSC is operating, the skid control ECU (brake actuator assembly) blinks the slip indicator light to inform the driver that slippage occurred.
When in VSC off mode, or TRAC a
SEE MORE:
Terminals Of Ecu
TERMINALS OF ECU TERMINALS OF ECU
*a Component without harness connected
(Skid Control ECU (Brake Actuator Assembly))
- -
HINT:
As a waterproof connector is used for the brake actuator assembly, voltage and waveform inspections cannot be performed with the connector c
Multi-axis Acceleration Sensor Module "A" Component Internal Failure (C052096)
DESCRIPTION The airbag sensor assembly has a built-in yaw rate and acceleration sensor and detects the vehicle condition.
The skid control ECU (brake actuator assembly) receives signals from the yaw rate and acceleration sensor (airbag sensor assembly) via CAN communication. These DTCs may be stor
