Toyota Camry (XV70): Test Mode Procedure

TEST MODE PROCEDURE

SENSOR CHECK USING DEALER MODE (SIGNAL CHECK)

NOTICE:

• After replacing or removing and installing a speed sensor, perform Dealer Mode (Signal Check) inspection to confirm that the speed sensors are operating correctly.
• After replacing or removing and installing a speed sensor rotor, perform Dealer Mode (Signal Check) inspection to confirm that the speed sensors are operating correctly.

HINT:

• Signals related to the vehicle stability control system can be inspected by performing a Dealer Mode (Signal Check) inspection. During the inspection, the display of items determined normal by the skid control ECU (brake actuator assembly) changes from incomplete to complete.
• During Dealer Mode (Signal Check), the VSC system does not operate regardless of whether the system is normal or a malfunction is detected.
• If a sensor is malfunctioning, ABS does not operate and the ABS warning and slip indicator lights illuminate.
• When entering Dealer Mode (Signal Check), the skid control ECU (brake actuator assembly) communicates with the forward recognition camera to judge whether the vehicle is equipped with the pre-collision system. Therefore, do not exit Dealer Mode (Signal Check) within 5 seconds of entering Dealer Mode (Signal Check). (w/ Pre-collision System)

(a) Procedure to enter Dealer Mode (Signal Check)

(1) Turn the ignition switch off.

(2) Apply the parking brake.

(3) Check that the shift lever is in P.

(4) Connect the Techstream to the DLC3.

(5) Turn the ignition switch to ON.

(6) Check that the steering wheel is centered.

(7) Turn the Techstream on.

(8) Switch the skid control ECU (brake actuator assembly) to Dealer Mode (Signal Check) using the Techstream. Enter the following menus: Chassis / Brake / Utility / Signal Check.

HINT:

Do not exit Dealer Mode (Signal Check) within 5 seconds of entering Dealer Mode (Signal Check). If Dealer Mode (Signal Check) is exited within 5 seconds of entering Dealer Mode (Signal Check), DTC U023A87 may be stored. If DTC U023A87 is output after exiting Dealer Mode (Signal Check), enter Dealer Mode (Signal Check) again, wait at least 5 seconds, then recheck for DTCs.

(b) Confirm the system has entered Dealer Mode (Signal Check).

(1) Confirm that the ABS warning light and slip indicator light indicate the Dealer Mode pattern (blinking at 0.25 seconds intervals).

HINT:

If the ABS warning light or slip indicator light remains illuminated or does not illuminate when Dealer Mode (Signal Check) is entered, a component or wire harness may be malfunctioning.

(c) Speed Sensor Check

(1) Start the engine.

(2) Drive the vehicle straight-ahead.

Accelerate the vehicle to a speed of 45 km/h (28 mph) or more for several seconds.

(3) Check that the ABS warning light goes off.

NOTICE:

• If the sensor check does not complete successfully or a malfunctioning sensor is detected, the ABS warning light indicates the Dealer Mode pattern (blinking at 0.25 seconds intervals) and the ABS system will not operate.
• If the vehicle is driven at 80 km/h (50 mph) or more after the ABS warning lamp turns off, the speed sensor check will be performed again. In this situation, the ABS warning lamp will start blinking again.
• The speed sensor check may not complete if the sensor check is started with the steering wheel turned or one or more wheels spinning.

HINT:

If the sensor check completes successfully, the ABS warning light turns off when the vehicle is being driven, and indicates the Dealer Mode pattern (blinking at 0.25 seconds intervals) when the vehicle is stopped.

(4) Stop the vehicle.

(d) VSC OFF Switch Check

(1) Press the VSC OFF switch.

(2) Check that the VSC OFF indicator light comes on.

(3) Press the VSC OFF switch again.

(4) Check that the VSC OFF indicator light turns off.

(e) End of Sensor Check

(1) If the sensor check completes successfully, the ABS warning light turns off when the vehicle is being driven, and indicates the Dealer Mode pattern (blinking at 0.25 seconds intervals) when the vehicle is stopped.

NOTICE:

• When the all Dealer Mode (Signal Check) Inspection Items are complete, the sensor check is complete.
• If the sensor checks have not completed, the ABS warning light will remain blinking while the vehicle is being driven, and the ABS will not operate.
• If any malfunctions are detected during Dealer Mode (Signal Check), the ABS warning light or slip indicator light remains illuminated.
• If any DTCs are output or if Dealer Mode (Signal Check) items do not complete even after repeated attempts, repair or replace the malfunctioning part.

(f) End of Dealer Mode (Signal Check)

(1) Turn the ignition switch off.

(2) Disconnect the Techstream.

(g) Dealer Mode (Signal Check) Inspection Item Chart

READ NEXT: