Toyota Camry (XV70): Transmission Range Sensor "A" Circuit Open (P070513,P070562)
DESCRIPTION
The park/neutral position switch assembly detects the shift lever position and sends signals to the ECM.
|
DTC No. | Detection Item |
DTC Detection Condition | Trouble Area |
MIL | Memory |
Note |
|---|---|---|---|---|---|---|
| P070513 |
Transmission Range Sensor "A" Circuit Open |
When the engine switch is on (IG) and battery voltage is 8 V or more, NSW, P, R, N and D input signals are all OFF simultaneously for 60 seconds or more (2-trip detection logic). |
| Comes on |
DTC stored | SAE Code: P0705 |
| P070562 |
Transmission Range Sensor "A" Signal Compare Failure |
When the engine switch is on (IG) and battery voltage is 8 V or more, 2 or more of the following signals are ON simultaneously for 2 seconds or more (2-trip detection logic).
|
| Comes on |
DTC stored | SAE Code: P0705 |
|
Vehicle Condition | |||||
|---|---|---|---|---|---|
|
Pattern 1 | Pattern 2 |
Pattern 3 | Pattern 4 | ||
|
Diagnostic Condition | Engine switch is on (IG) |
○ | ○ |
○ | ○ |
|
Battery voltage is 8 V or more |
○ | ○ |
○ | ○ | |
|
Malfunction Condition | NSW input signal is ON |
○ | ○ |
- | - |
|
P input signal is ON |
- | - |
○ | ○ | |
|
R input signal is ON |
- | ○ |
- | ○ | |
|
N input signal is ON |
- | - |
- | - | |
|
D input signal is ON |
○ | - |
○ | - | |
|
Duration | 2 seconds or more |
2 seconds or more | 2 seconds or more |
2 seconds or more | |
|
Detection Logic | 2-trip detection logic |
2-trip detection logic |
2-trip detection logic |
2-trip detection logic | |
|
Vehicle Condition | ||||
|---|---|---|---|---|
|
Pattern 5 | Pattern 6 |
Pattern 7 | ||
|
Diagnostic Condition | Engine switch is on (IG) |
○ | ○ |
○ |
| Battery voltage is 8 V or more |
○ | ○ |
○ | |
|
Malfunction Condition | NSW input signal is ON |
- | - |
- |
| P input signal is ON |
- | - |
- | |
| R input signal is ON |
- | ○ |
○ | |
| N input signal is ON |
○ | ○ |
- | |
| D input signal is ON |
○ | - |
○ | |
|
Duration | 2 seconds or more |
2 seconds or more | 2 seconds or more | |
|
Detection Logic | 2-trip detection logic |
2-trip detection logic |
2-trip detection logic | |
HINT:
DTC P070562 is stored when any of the above detection patterns is met.
MONITOR DESCRIPTION
These DTCs indicate a problem with the park/neutral position switch assembly or the wire harness in the park/neutral position switch assembly circuit.
The park/neutral position switch assembly detects the shift lever position and sends signals to the ECM.
For safety, the park/neutral position switch assembly detects the shift lever position so that the engine can be started only when the shift lever is in P or N.
The park/neutral position switch assembly sends a signal to the ECM according to the shift lever position (P, N, R, D or S).
The ECM determines that there is a problem with the switch or related parts if it receives more than 1 position signal simultaneously and will then illuminate the MIL and store a DTC.
MONITOR STRATEGY
|
Related DTCs | P0705: Park/neutral position switch assembly/Verify switch input |
|
Required sensors/components |
Park/neutral position switch |
|
Frequency of operation |
Continuous |
| Duration |
Condition (A): 2 sec. Condition (B): 60 sec. |
|
MIL operation | 2 driving cycles |
|
Sequence of operation | None |
TYPICAL ENABLING CONDITIONS
|
The monitor will run whenever the following DTCs are not stored |
None |
| Engine switch |
On (IG) |
| Battery voltage |
8 V or more |
| Starter |
OFF |
TYPICAL MALFUNCTION THRESHOLDS
Either of the following conditions is met: Condition (A) or (B)
Condition (A)|
Any two of the following conditions are met: |
Conditions 1, 2 and 3 |
| 1. One of the following conditions is met: |
Conditions (a), (b) or (c) |
|
(a) P position switch | ON |
|
(b) N position switch | ON |
|
(c) Park/neutral position switch (NSW) |
ON |
| 2. R position switch |
ON |
| 3. D position switch |
ON |
|
All of following conditions are met: |
- |
| P position switch |
OFF |
| N position switch |
OFF |
| Park/neutral position switch (NSW) |
OFF |
| R position switch |
OFF |
| D position switch |
OFF |
COMPONENT OPERATING RANGE
|
Park/neutral position switch |
The park/neutral position switch sends only one signal to the ECM |
CONFIRMATION DRIVING PATTERN
HINT:
- After repairs have been completed, clear the DTCs and then check that the vehicle has returned to normal by performing the following All Readiness check procedure.
- When clearing the permanent DTCs, refer to the Clear Permanent DTC procedure.
Click here
.gif)
- Connect the Techstream to the DLC3.
- Turn the engine switch on (IG) and turn the Techstream on.
- Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).
- Turn the engine switch off and wait for 2 minutes or more.
- Turn the engine switch on (IG) and turn the Techstream on.
- Wait with the shift lever in each position (P, R, N and D) for 60 seconds or more each with the engine switch on (IG). [*1]
HINT:
[*1] : Normal judgment procedure.
The normal judgment procedure is used to complete DTC judgment and also used when clearing permanent DTCs.
- Enter the following menus: Powertrain / Transmission / Utility / All Readiness.
- Input the DTC: P070513 or P070562.
- Check the DTC judgment result.
Techstream Display
Description
NORMAL
- DTC judgment completed
- System normal
ABNORMAL
- DTC judgment completed
- System abnormal
INCOMPLETE
- DTC judgment not completed
- Perform driving pattern after confirming DTC enabling conditions
N/A
- Unable to perform DTC judgment
- Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit
HINT:
- If the judgment result shows NORMAL, the system is normal.
- If the judgment result shows ABNORMAL, the system has a malfunction.
- If the judgment result shows INCOMPLETE or N/A, perform the normal judgment procedure again.
WIRING DIAGRAM
CAUTION / NOTICE / HINT
NOTICE:
- Inspect the fuses for circuits related to this system before performing the following procedure.
- Perform the universal trip to clear permanent DTCs.
Click here
- Perform registration and/or initialization when parts related to the automatic transaxle are replaced.
Click here
PROCEDURE
|
1. | CHECK HARNESS AND CONNECTOR (BATTERY - PARK/NEUTRAL POSITION SWITCH ASSEMBLY) |
(a) Disconnect the C55 park/neutral position switch assembly connector.
(b) Turn the engine switch on (IG).
(c) Measure the voltage according to the value(s) in the table below.
Standard Voltage:
|
Tester Connection | Switch Condition |
Specified Condition |
|---|---|---|
|
C55-1 (RB) - Body ground |
Engine switch on (IG) |
11 to 14 V |
|
C55-1 (RB) - Body ground |
Engine switch off | Below 1 V |
| NG | .gif) | REPAIR OR REPLACE HARNESS OR CONNECTOR |
|
.gif)
| 2. |
CHECK HARNESS AND CONNECTOR (OUTPUT SIGNAL) |
(a) Disconnect the C55 park/neutral position switch assembly connector.
(b) Turn the engine switch on (IG).
(c) Measure the voltage according to the value(s) in the table below.
Standard Voltage:
|
Tester Connection | Switch Condition |
Specified Condition |
|---|---|---|
|
C55-4 (B) - Body ground |
Engine switch on (IG) |
11 to 14 V |
|
C55-4 (B) - Body ground |
Engine switch off | Below 1 V |
| NG | | GO TO STEP 6 |
|
| 3. |
INSPECT PARK/NEUTRAL POSITION SWITCH ASSEMBLY |
| (a) Disconnect the C55 park/neutral position switch assembly connector. |
|
(b) Measure the resistance according to the value(s) in the table below.
Standard Resistance:
|
Tester Connection | Condition |
Specified Condition |
|---|---|---|
|
4 (B) - 9 (L) | Shift lever in P or N |
Below 1 Ω |
|
1 (RB) - 3 (PL) | Shift lever in P |
Below 1 Ω |
|
1 (RB) - 2 (RL) | Shift lever in R |
Below 1 Ω |
|
1 (RB) - 8 (NL) | Shift lever in N |
Below 1 Ω |
|
1 (RB) - 7 (DL) | Shift lever in D, S, "+" or "-" |
Below 1 Ω |
|
4 (B) - 9 (L) | Shift lever not in P or N |
10 kΩ or higher |
|
1 (RB) - 3 (PL) | Shift lever not in P |
10 kΩ or higher |
|
1 (RB) - 2 (RL) | Shift lever not in R |
10 kΩ or higher |
|
1 (RB) - 8 (NL) | Shift lever not in N |
10 kΩ or higher |
|
1 (RB) - 7 (DL) | Shift lever not in D, S, "+" or "-" |
10 kΩ or higher |
| NG | | REPLACE PARK/NEUTRAL POSITION SWITCH ASSEMBLY |
|
| 4. |
CHECK HARNESS AND CONNECTOR (PARK/NEUTRAL POSITION SWITCH ASSEMBLY - ECM) |
(a) Connect the C55 park/neutral position switch assembly connector.
(b) Disconnect the C96 ECM connector.
(c) Turn the engine switch on (IG).
(d) Measure the voltage according to the value(s) in the table below.
Standard Voltage:
|
Tester Connection | Condition |
Specified Condition |
|---|---|---|
|
C96-108 (P) - Body ground |
| 11 to 14 V |
|
C96-107 (R) - Body ground |
| 11 to 14 V* |
|
C96-140 (N) - Body ground |
| 11 to 14 V |
|
C96-139 (D) - Body ground |
| 11 to 14 V |
|
C96-108 (P) - Body ground |
| Below 1 V |
|
C96-107 (R) - Body ground |
| Below 1 V |
|
C96-140 (N) - Body ground |
| Below 1 V |
|
C96-139 (D) - Body ground |
| Below 1 V |
HINT:
*: The voltage will drop slightly due to the illumination of the back up lights.
| NG | | REPAIR OR REPLACE HARNESS OR CONNECTOR (PARK/NEUTRAL POSITION SWITCH ASSEMBLY - ECM) |
|
| 5. |
REPLACE ECM |
(a) Replace the ECM.
Click here
| NEXT | | PERFORM REGISTRATION |
| 6. |
CHECK HARNESS AND CONNECTOR (PARK/NEUTRAL POSITION SWITCH ASSEMBLY - ECM) |
(a) Disconnect the C55 park/neutral position switch assembly connector.
(b) Disconnect the C96 ECM connector.
(c) Measure the resistance according to the value(s) in the table below.
Standard Resistance:
|
Tester Connection | Condition |
Specified Condition |
|---|---|---|
|
C55-4 (B) - C96-106 (NSW) |
Always | Below 1 Ω |
|
C55-4 (B) or C96-106 (NSW) - Body ground and other terminals |
Always | 10 kΩ or higher |
| NG | | REPAIR OR REPLACE HARNESS OR CONNECTOR (PARK/NEUTRAL POSITION SWITCH ASSEMBLY - ECM) |
|
| 7. |
REPLACE ECM |
(a) Replace the ECM.
Click here
| NEXT | | PERFORM REGISTRATION |
READ NEXT:
Transmission Fluid Temperature Sensor "A" Circuit Range/Performance (P071000)
DESCRIPTION The ATF temperature sensor converts the automatic transaxle fluid (ATF) temperature into a resistance value for use by the ECM.
The ECM applies a voltage to the temperature sensor throug
Transmission Fluid Temperature Sensor "A" Circuit Short To Ground (P071011)
DESCRIPTION The ATF temperature sensor converts the automatic transaxle fluid (ATF) temperature into a resistance value for use by the ECM.
The ECM applies voltage to the temperature sensor through
Transmission Fluid Temperature Sensor "A" Circuit Short to Battery or Open (P071015)
DESCRIPTION The ATF temperature sensor converts the automatic transaxle fluid (ATF) temperature into a resistance value for use by the ECM.
The ECM applies voltage to the temperature sensor through
SEE MORE:
Terminals Of Ecu
TERMINALS OF ECU TERMINALS OF ECU
*a Component without harness connected
(Skid Control ECU (Brake Actuator Assembly))
- -
HINT:
As a waterproof connector is used for the brake actuator assembly, voltage and waveform inspections cannot be performed with the connector c
On-vehicle Inspection
ON-VEHICLE INSPECTION PROCEDURE
1. INSPECT PARKING BRAKE ACTUATOR ASSEMBLY (a) With the ignition switch ON and the wheels not contacting the ground, operate the electric parking brake switch assembly to check the condition of the rear wheels when the electric parking brake is operating and not ope
