Toyota Camry (XV70): Ultrasonic Sensor (Front Right Corner) Missing Message (C1AE487)
DESCRIPTION
This DTC is stored when an open circuit or short occurs in the communication line between the front corner ultrasonic sensor RH and the clearance warning ECU, or when a malfunction occurs in the front corner ultrasonic sensor RH.
|
DTC No. | Detection Item |
DTC Detection Condition | Trouble Area |
|---|---|---|---|
|
C1AE487 | Ultrasonic Sensor (Front Right Corner) Missing Message |
Front corner ultrasonic sensor RH lost communication |
|
WIRING DIAGRAM
CAUTION / NOTICE / HINT
NOTICE:
- Perform registration after replacing or removing and installing the ultrasonic sensor or clearance warning ECU assembly.
Click here
.gif)
- If a DTC is detected again after the repair, turn the ignition switch to ON and turn the intuitive parking assist system on, and then clear the DTC.
Click here
PROCEDURE
|
1. | VEHICLE CONDITION AND WORK DETAILS CHECK |
(a) Check the vehicle condition and work details.
|
Result | Proceed to |
|---|---|
|
The clearance warning ECU assembly or ultrasonic sensor has not been replaced |
A |
| The clearance warning ECU assembly or ultrasonic sensor has been replaced |
B |
| B |
.gif) | GO TO CALIBRATION |
|
.gif)
| 2. |
CHECK CONNECTOR CONNECTION CONDITION (ULTRASONIC SENSOR) |
(a) Check that the connector is properly connected to the front corner ultrasonic sensor and front center ultrasonic sensor.
|
| 3. |
CHECK FOR DTC |
(a) According to the display on the GTS, check for DTCs.
Body Electrical > Clearance Warning > Trouble Codes(b) According to the display on the GTS, clear the DTCs.
Body Electrical > Clearance Warning > Clear DTCs(c) Recheck for DTCs.
Body Electrical > Clearance Warning > Trouble Codes|
Result | Proceed to |
|---|---|
|
C1AE487 is not output |
A |
| C1AE487 is output |
B |
| A |
| END (CONNECTOR CONNECTION MALFUNCTION) |
|
| 4. |
CHECK CONNECTOR CONNECTION CONDITION (CLEARANCE WARNING ECU ASSEMBLY) |
(a) Check that the connector is properly connected to the clearance warning ECU assembly.
|
| 5. |
CHECK FOR DTC |
(a) According to the display on the GTS, check for DTCs.
Body Electrical > Clearance Warning > Trouble Codes(b) According to the display on the GTS, clear the DTCs.
Body Electrical > Clearance Warning > Clear DTCs(c) Recheck for DTCs.
Body Electrical > Clearance Warning > Trouble Codes DTC OUTPUT COMBINATION:|
Symptoms | DTC Detection | |||
|---|---|---|---|---|
|
C1AE487 | C1AE387 |
C1AE287 | C1AE187 | |
|
Symptom 1 | Not output |
Not output | Not output |
Not output |
|
Symptom 2 | Output |
Output | Output |
Output |
| Symptom 3 |
Not output | Output |
Output | Output |
|
Symptom 4 | Not output |
Not output | Output |
Output |
| Symptom 5 |
Not output | Not output |
Not output | Output |
|
Symptom 6 | Output |
Not output | Not output |
Not output |
|
Result | Proceed to |
|---|---|
|
Listed under symptom 1 in combination table |
A |
| Listed under symptom 2 in combination table |
B |
| Listed under symptom 3 in combination table |
C |
| Listed under symptom 4 in combination table |
D |
| Listed under symptom 5 in combination table |
E |
| Listed under symptom 6 in combination table |
F |
| A |
| USE SIMULATION METHOD TO CHECK
|
| C |
| GO TO CORRESPONDING FLOWCHART (INTUITIVE PARKING ASSIST SYSTEM (C1AE387)) |
| D |
| GO TO CORRESPONDING FLOWCHART (INTUITIVE PARKING ASSIST SYSTEM (C1AE287)) |
| E |
| GO TO CORRESPONDING FLOWCHART (INTUITIVE PARKING ASSIST SYSTEM (C1AE187)) |
| F |
| GO TO STEP 7 |
|
| 6. |
CHECK WIRE HARNESS AND CONNECTOR (CLEARANCE WARNING ECU - FRONT CORNER ULTRASONIC SENSOR RH) |
(a) Disconnect the R39 clearance warning ECU connector.
(b) Disconnect the B8 front corner ultrasonic sensor RH connector.
(c) Measure the resistance according to the value(s) in the table below.
Standard Resistance:
|
Tester Connection | Condition |
Specified Condition |
|---|---|---|
|
R39-2 (BOF) - B8-4 (BI) |
Always | Below 1 Ω |
|
R39-4 (SOF) - B8-5 (SI) |
Always | Below 1 Ω |
|
R39-3 (E5) - B8-6 (EI) |
Always | Below 1 Ω |
|
R39-2 (BOF) or B8-4 (BI) - Body ground |
Always | 10 kΩ or higher |
|
R39-4 (SOF) or B8-5 (SI) - Body ground |
Always | 10 kΩ or higher |
|
R39-3 (E5) or B8-6 (EI) - Body ground |
Always | 10 kΩ or higher |
| NG | | REPAIR OR REPLACE WIRE HARNESS OR CONNECTOR |
|
| 7. |
REPLACE FRONT CORNER ULTRASONIC SENSOR RH |
(a) Replace the front corner ultrasonic sensor RH with a new or normally functioning one.
Click here
HINT:
To check if the ultrasonic sensor is functioning correctly, replace it with another ultrasonic sensor.
|
| 8. |
RECHECK FOR DTC |
(a) According to the display on the GTS, check for DTCs.
Body Electrical > Clearance Warning > Trouble Codes(b) According to the display on the GTS, clear the DTCs.
Body Electrical > Clearance Warning > Clear DTCs(c) Recheck for DTCs.
Body Electrical > Clearance Warning > Trouble Codes|
Result | Proceed to |
|---|---|
|
No DTC is output | A |
|
"C1AE487" is output | B |
| A |
| END (FRONT CORNER ULTRASONIC SENSOR RH WAS DEFECTIVE) |
| B |
| REPLACE CLEARANCE WARNING ECU ASSEMBLY |
READ NEXT:
SEE MORE:
Radio Receiver Power Source Circuit
DESCRIPTION This is the power source circuit to operate the radio and display receiver assembly. WIRING DIAGRAM
CAUTION / NOTICE / HINT
NOTICE: Inspect the fuses for circuits related to this system before performing the following procedure. PROCEDURE
1.
CHECK HARNESS AND CONNECTOR (R
Inspection
INSPECTION PROCEDURE 1. INSPECT WATER INLET WITH THERMOSTAT SUB-ASSEMBLY
(a) Check the valve opening. HINT: The valve opening temperature is inscribed on the water inlet with thermostat sub-assembly.
(1) Add 15 cc (0.9 cu. in.) of water to the water inlet with thermostat sub-assembly from
