Toyota Camry (XV70): Adjustment
ADJUSTMENT
PROCEDURE
1. INSPECT PARKING BRAKE PEDAL TRAVEL
(a) Completely release the parking brake pedal assembly.
(b) Fully depress the parking brake pedal assembly to engage the parking brake.
(c) Depress the parking brake pedal assembly again to disengage the parking brake.
| (d) Slowly depress the parking brake pedal assembly using the specified force, and count the number of clicks. Parking Brake Pedal Travel: 7 to 12 notches at 300 N (31 kgf, 67.4 lbf) If the parking brake pedal travel is not as specified, adjust the parking brake shoe clearance and parking brake pedal travel. |
|
2. ADJUST PARKING BRAKE PEDAL TRAVEL
(a) Completely release the parking brake pedal assembly.
| (b) Turn the No. 1 wire adjusting nut until the parking brake pedal travel is corrected to within the specified range. Parking Brake Pedal Travel: 7 to 12 notches at 300 N (31 kgf, 67.4 lbf) NOTICE: If the No. 1 wire adjusting nut has been removed from the No. 1 parking brake cable assembly, replace the No. 1 wire adjusting nut with a new one. |
|
.png)
(c) Remove the rear wheels.
Click here
.gif)
(d) Temporarily install the hub nuts to the hub bolts.
HINT:
Make sure to tighten the hub nuts so that the rear disc is secure.
(e) Remove the parking brake shoe adjusting hole plug.
(f) Turn the parking brake shoe adjuster and expand the shoes until the disc locks.
.png) |
Contract |
.png) |
Expand |
(g) Turn and contract the parking brake shoe adjuster until the rear disc can rotate smoothly.
Standard:
Returns 8 notches.
(h) Check that there is no brake drag against the shoe.
(i) Operate the parking brake pedal assembly 3 to 4 times.
(j) Turn the No. 1 wire adjusting nut until the parking brake pedal travel is corrected to be within the specified range.
Parking Brake Pedal Travel:
7 to 12 notches at 300 N (31 kgf, 67.4 lbf)
(k) Operate the parking brake pedal assembly 3 to 4 times.
(l) Check the parking brake pedal travel.
Parking Brake Pedal Travel:
7 to 12 notches at 300 N (31 kgf, 67.4 lbf)
(m) Install the parking brake shoe adjusting hole plug.
(n) Check that the parking brake does not drag.
(o) Remove the hub nuts from the hub bolts.
(p) Install the rear wheels.
Click here
3. INSPECT BRAKE WARNING LIGHT
(a) When operating the parking brake pedal assembly, check that the brake warning light illuminates.
Standard:
The brake warning light always illuminates at the first click.
READ NEXT:
Parking Brake System(w/ Electric Parking Brake System)
PrecautionPRECAUTION
NOTICE:
If the battery is connected, the parking brake will operate when the electric parking brake switch assembly is pulled to the lock side even if the engine switch is o
SEE MORE:
Installation
INSTALLATION PROCEDURE 1. INSTALL CAMSHAFT TIMING GEAR BOLT
(a) Make sure that the No. 1 cylinder is at TDC/compression. HINT:
Check that the cutout of the camshaft timing gear assembly is at the top and align the timing mark (cutout) of the crankshaft pulley with the timing mark on the timing c
ABS Operates Before Necessary When Braking
DESCRIPTION Troubleshooting for when ABS operates too soon due to a noisy signal from the speed sensor, a difference in output, etc. CAUTION / NOTICE / HINT
NOTICE:
After replacing or removing and installing a speed sensor, perform Dealer Mode (Signal Check) inspection to confirm that the spee
