Toyota Camry (XV70): Air Conditioner ECU Vehicle Information Reading/Writing Processor Malfunction (B15F5)
DESCRIPTION
This DTC is stored when items controlled by the air conditioning amplifier assembly cannot be customized via the audio and visual system vehicle customization screen.
HINT:
The air conditioning amplifier assembly controls the air conditioning system related items that are customizable via the audio and visual system vehicle customization screen.
|
DTC No. | Detection Item |
DTC Detection Condition | Trouble Area |
|---|---|---|---|
|
B15F5 | Air Conditioner ECU Vehicle Information Reading/Writing Processor Malfunction |
Air conditioning amplifier assembly vehicle setting processing malfunction |
|
CAUTION / NOTICE / HINT
NOTICE:
- Depending on the parts that are replaced during vehicle inspection or maintenance, performing initialization, registration or calibration may be needed. Refer to Precaution for Audio and Visual System.
Click here
.gif)
- When replacing the radio and display receiver assembly, always replace it with a new one. If a radio and display receiver assembly which was installed to another vehicle is used, the following may occur:
- A communication malfunction DTC may be stored.
- The radio and display receiver assembly may not operate normally.
PROCEDURE
|
1. | CHECK CAN COMMUNICATION SYSTEM |
(a) Use the Techstream to check if the CAN communication system is functioning normally.
Click here
OK:
CAN communication DTCs are not output.
| NG | .gif) | GO TO CAN COMMUNICATION SYSTEM |
|
.gif)
| 2. |
CHECK AIR CONDITIONING SYSTEM |
(a) Check if the air conditioning system is malfunctioning.
Click here
HINT:
Customization may not be possible depending on the malfunction in the air conditioning system.
OK:
No malfunctions are present in the air conditioning system.
| NG | | GO TO AIR CONDITIONING SYSTEM
|
|
| 3. |
CHECK CUSTOMIZE ITEMS |
(a) Make a note of the customizable items for the air conditioning system.
HINT:
The items shown as customizable via the audio and visual system vehicle customization screen can also be changed using the Techstream. In the following step, the Techstream will be used.
(1) To match-up the items on the audio and visual system vehicle customization screen with the items on the Techstream, check the customize parameters list for the air conditioning system related items that can be customized via the audio and visual system vehicle customization screen.
Click here
(b) Using the Techstream, check that it is possible to change the settings of the customize parameters that are available for customization via the audio and visual system vehicle customization screen.
OK:
The items available for customization via the audio and visual system vehicle customization screen can be customized successfully using the Techstream.
| OK | | REPLACE RADIO AND DISPLAY RECEIVER ASSEMBLY
|
| NG | | REPLACE AIR CONDITIONING AMPLIFIER ASSEMBLY
|
READ NEXT:
Main Body ECU Vehicle Information Reading/Writing Process Malfunction (B15F6)
DESCRIPTION This DTC is stored when items controlled by the main body ECU (multiplex network body ECU) cannot be customized via the audio and visual system vehicle customization screen.
HINT: The ma
Certification ECU Vehicle Information Reading/Writing Process Malfunction (B15F7)
DESCRIPTION This DTC is stored when items controlled by the certification ECU (smart key ECU assembly) cannot be customized via the audio and visual system vehicle customization screen.
HINT: The ce
XM Tuner Antenna Disconnected (B15FE,B15FF)
DESCRIPTION These DTCs are stored when a malfunction occurs in the roof antenna assembly which is connected to the radio and display receiver assembly.
DTC No. Detection Item
DTC Detectio
SEE MORE:
Inspection
INSPECTION PROCEDURE 1. INSPECT FRONT DRIVE SHAFT ASSEMBLY
(a) Check that there is no excessive play in the radial direction of the outboard joint.
(b) Check that the inboard joint slides smoothly in the thrust direction.
(c) Check that there is no excessive play in the
VSC OFF Switch Circuit
DESCRIPTION The skid control ECU (brake actuator assembly) is connected to the combination meter assembly via CAN communication.
Pressing the VSC OFF switch turns off TRAC operation, and pressing and holding this switch turns off TRAC and VSC operation. If TRAC and VSC operations are turned off, "
