Toyota Camry (XV70): Multi-axis Acceleration Sensor Module "A" Component Internal Failure (C052096)
DESCRIPTION
The airbag sensor assembly has a built-in yaw rate and acceleration sensor and detects the vehicle condition.
The skid control ECU (brake actuator assembly) receives signals from the yaw rate and acceleration sensor (airbag sensor assembly) via CAN communication.
These DTCs may be stored if one of the following occurs:- Yaw rate and acceleration sensor (airbag sensor assembly) installation abnormality.
- Yaw rate and acceleration sensor signal malfunction.
|
DTC No. | Detection Item |
DTC Detection Condition | Trouble Area |
|---|---|---|---|
|
C052096 | Multi-axis Acceleration Sensor Module "A" Component Internal Failure |
|
|
|
Vehicle Condition | ||||||
|---|---|---|---|---|---|---|
|
Pattern 1 | Pattern 2 |
Pattern 3 | Pattern 4 |
Pattern 5 | ||
|
Diagnosis Condition | The vehicle is being driven. |
○ | ○ |
- | - |
- |
| With the +BS terminal voltage between 9.6 and 16.5 V. |
- | - |
○ | - |
- | |
|
Malfunction Status | The offset of the acceleration sensor is less than -2.25 m/s2. |
○ | - |
- | - |
- |
| The offset of the acceleration sensor is more than 2.25 m/s2. |
- | ○ |
- | - |
- | |
| An acceleration sensor internal malfunction signal is received from the acceleration sensor (airbag sensor assembly). |
- | - |
○ | - |
- | |
| The value (Forward and rearward G) of the acceleration sensor is less than -14.6 m/s2. |
- | - |
- | ○ |
- | |
| The value (Forward and rearward G) of the acceleration sensor is more than 14.6 m/s2. |
- | - |
- | - |
○ | |
|
Detection Time | - |
- | - |
3 seconds or more. | 3 seconds or more. | |
|
Number of Trips | 1 trip |
1 trip | 1 trip |
1 trip | 1 trip | |
HINT:
DTC will be output when conditions for either of the patterns in the table above are met.
DTC Detection Conditions: C052096|
Vehicle Condition | |||||
|---|---|---|---|---|---|
|
Pattern 6 | Pattern 7 |
Pattern 8 | Pattern 9 | ||
|
Diagnosis Condition | The vehicle is stopped. |
○ | ○ |
- | - |
|
Malfunction Status | The value (lateral) of the acceleration sensor is less than -7 m/s2. |
○ | - |
- | - |
|
The value (lateral) of the acceleration sensor is more than 7 m/s2. |
- | ○ |
- | - | |
|
The value (lateral) of the acceleration sensor is less than -14.6 m/s2. |
- | - |
○ | - | |
|
The value (lateral) of the acceleration sensor is more than 14.6 m/s2. |
- | - |
- | ○ | |
|
Detection Time | 0.4 seconds or more. |
0.4 seconds or more. |
0.8 seconds or more. |
0.8 seconds or more. | |
|
Number of Trips | 1 trip |
1 trip | 1 trip |
1 trip | |
HINT:
DTC will be output when conditions for either of the patterns in the table above are met.
CAUTION / NOTICE / HINT
NOTICE:
After replacing or reinstalling the yaw rate and acceleration sensor (airbag sensor assembly), perform acceleration sensor zero point calibration and system information memorization after performing "Reset Memory".
Click here .gif)
PROCEDURE
| 1. |
CHECK FREEZE FRAME DATA (LATERAL G AND FORWARD AND REARWARD G) |
(a) Connect the Techstream to the DLC3.
(b) Turn the ignition switch to ON.
(c) Enter the following menus: Chassis / Brake/EPB / Trouble Codes.
(d) Select a DTC to display the Freeze Frame Data.
(e) Read the freeze frame data of DTC C052096.
Chassis > Brake|
Tester Display | Measurement Item |
Range | Normal Condition |
Diagnostic Note |
|---|---|---|---|---|
|
Lateral G | Lateral G |
Min.: -25.105 m/s2, Max.: 24.908 m/s2 |
Turning right: -25.105 to 0.000 m/s2 Turning left: 0.000 to 24.908 m/s2 |
During turning: Changes in proportion with lateral acceleration |
|
Forward and Rearward G |
Forward and rearward G |
Min.: -25.105 m/s2, Max.: 24.908 m/s2 |
During deceleration: -25.105 to 0.000 m/s2 During acceleration: 0.000 to 24.908 m/s2 |
During acceleration/deceleration: Changes in proportion with acceleration |
|
Tester Display |
|---|
| Lateral G |
|
Forward and Rearward G |
|
Result | Proceed to |
|---|---|
|
The value of Lateral G or Forward and rearward G is less than -14.6 m/s2 or more than 14.6 m/s2. |
A |
| Other than above. |
B |
| A |
.gif) | REPLACE AIRBAG SENSOR ASSEMBLY |
|
.gif)
| 2. |
CHECK FREEZE FRAME DATA (LATERAL G AND VEHICLE SPEED) |
(a) Connect the Techstream to the DLC3.
(b) Turn the ignition switch to ON.
(c) Enter the following menus: Chassis / Brake/EPB / Trouble Codes.
(d) Select a DTC to display the Freeze Frame Data.
(e) Read the freeze frame data of DTC C052096.
Chassis > Brake|
Tester Display | Measurement Item |
Range | Normal Condition |
Diagnostic Note |
|---|---|---|---|---|
|
Lateral G | Lateral G |
Min.: -25.105 m/s2, Max.: 24.908 m/s2 |
Turning right: -25.105 to 0.000 m/s2 Turning left: 0.000 to 24.908 m/s2 |
During turning: Changes in proportion with lateral acceleration |
|
Vehicle Speed | Vehicle speed (vehicle speed used for each control) |
Min.: 0.0 km/h (0 mph), Max.: 6553.5 km/h (4072 mph) |
Vehicle stopped: 0.0 km/h (0.0 mph) |
When driving at constant speed: No large fluctuations |
|
Tester Display |
|---|
| Lateral G |
|
Vehicle Speed |
|
Result | Proceed to |
|---|---|
|
The value of Vehicle speed is 0 km/h (0 mph) and the value of Lateral G is less than -7 m/s2 or more than 7 m/s2. |
A |
| Other than above. |
B |
| A |
| REPLACE AIRBAG SENSOR ASSEMBLY |
|
| 3. |
CHECK AIRBAG SENSOR ASSEMBLY INSTALLATION |
(a) Check that the yaw rate and acceleration sensor (airbag sensor assembly) has been installed properly.
Click here
OK:
The yaw rate and acceleration sensor (airbag sensor assembly) is tightened to the specified torque.
The yaw rate and acceleration sensor (airbag sensor assembly) is not installed in a tilted position.
| OK | | REPLACE AIRBAG SENSOR ASSEMBLY |
| NG | | INSTALL AIRBAG SENSOR ASSEMBLY CORRECTLY |
READ NEXT:
Steering Angle Sensor Module Circuit Voltage Out of Range (C05261C)
DESCRIPTION The skid control ECU (brake actuator assembly) compares the calculated steering angle value based on the yaw rate sensor value with the actual steering angle value of the steering sensor.
Steering Angle Sensor Module Signal Stuck In Range (C05262A)
DESCRIPTION The skid control ECU (brake actuator assembly) determines the steering angle value based on data obtained from the steering sensor, yaw rate and acceleration sensor (airbag sensor assembly
Steering Angle Sensor Module Calibration / Parameter Memory Failure (C052646)
DESCRIPTION When the vehicle is being driven in a straight line at 15 km/h (9 mph) for 1 second or more, the skid control ECU (brake actuator assembly) calculates the steering angle sensor zero point
SEE MORE:
Removal
REMOVAL CAUTION / NOTICE / HINT
The necessary procedures (adjustment, calibration, initialization or registration) that must be performed after parts are removed and installed, or replaced during brake booster assembly removal/installation are shown below. Necessary Procedures After Parts Removed/
Data Signal Circuit between Radio Receiver and Stereo Jack Adapter
DESCRIPTION The No. 1 stereo jack adapter assembly sends the sound data signal or image data signal from a USB device to the radio and display receiver assembly via this circuit. WIRING DIAGRAM
PROCEDURE
1.
CHECK HARNESS AND CONNECTOR (RADIO AND DISPLAY RECEIVER ASSEMBLY - NO. 1 STEREO
