Toyota Camry (XV70): Portable Player cannot be Connected Manually/Automatically
CAUTION / NOTICE / HINT
HINT:
Some versions of "Bluetooth" compatible audio players may not function properly, or the functions may be limited using the radio and display receiver assembly, even if the portable audio player itself can play files.
Click here .gif)
PROCEDURE
| 1. |
CHECK CONNECTED DEVICE SETTINGS |
(a) Check if the portable player is registered as a connected device.
NOTICE:
If a cellular phone is used as a portable player, it must be registered independently from the registration that is performed for the hands-free system.
HINT:
Only 5 portable players can be registered.
|
Result | Proceed to |
|---|---|
|
The portable player is registered as a connected device. |
A |
| The portable player is not registered as a connected device. |
B |
| B |
.gif) | REGISTER PORTABLE PLAYER AS CONNECTED DEVICE |
|
.gif)
| 2. |
CHECK SYMPTOMS |
(a) Check the connection condition between the portable player and the radio and display receiver assembly.
HINT:
The portable player cannot be connected under any of the following conditions:
- The portable player is connected to another device.
- The portable player is connected to the radio and display receiver assembly using the hands-free function.
- The radio and display receiver assembly has cleared the portable player registration.
- The portable player is off.
|
Result | Proceed to |
|---|---|
|
The portable player cannot be connected automatically. |
A |
| The portable player cannot be connected manually. |
B |
| B |
| GO TO STEP 4 |
|
| 3. |
CHECK AUTOMATIC CONNECTION SETTINGS |
(a) Check the automatic connection settings of the "Bluetooth" audio.
(1) Check that the "Bluetooth" connection setting is on.
OK:
"Bluetooth" connection setting is on.
| NG | | TURN "Bluetooth" POWER TO ON |
|
| 4. |
CHECK PORTABLE PLAYER STATUS |
(a) Check the status of the portable player.
(1) Check that the portable player is not in standby mode.
(2) Check that the portable player is not connected to another device (headphones, etc.).
OK:
The portable player is not in standby mode and not connected to another device (headphones, etc.).
| NG | | TAKE PORTABLE PLAYER OUT OF STANDBY MODE AND DISCONNECT OTHER DEVICES (HEADPHONES, etc.) |
|
| 5. |
CHECK USING ANOTHER "Bluetooth" AUDIO COMPATIBLE VEHICLE OF SAME MODEL |
(a) Check if the portable player can be connected manually/automatically to another "Bluetooth" audio compatible vehicle of the same model.
OK:
The portable player can be connected manually/automatically.
| NG | | PORTABLE PLAYER IS NOT COMPATIBLE |
|
| 6. |
REMOVE ADDITIONAL DEVICES WHICH USE RADIO WAVES |
(a) Remove additional devices which use radio waves.
(b) Check if the portable player can be connected manually/automatically.
OK:
The portable player can be connected manually/automatically.
| OK | | END |
| NG | | PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE
|
READ NEXT:
Registered Device cannot be Deleted
PROCEDURE
1. DELETE OPERATION
(a) Check if a registered portable player can be deleted normally. OK:
Registered portable player can be deleted normally.
OK
END
NG
Portable Player cannot be Registered
CAUTION / NOTICE / HINT HINT: Some versions of "Bluetooth" compatible audio players may not function properly, or the functions may be limited using the radio and display receiver assembly, even if th
USB Audio System Recognition/Play Error
DESCRIPTION When a USB device or "iPod" is connected to the USB jack of the No. 1 stereo jack adapter assembly, it must have playable files. The device must also communicate with and be recognized by
SEE MORE:
Installation
INSTALLATION CAUTION / NOTICE / HINT
NOTICE:
Immediately after installing the brake pads, the braking performance may be reduced. Always perform a road test in a safe place while paying attention to the surroundings.
After replacing the front disc brake pads, the brake pedal may feel soft
Reverse Signal Circuit between Radio Receiver Assembly and Navigation ECU
DESCRIPTION This circuit includes the navigation ECU and radio and display receiver assembly. WIRING DIAGRAM
PROCEDURE
1.
CHECK HARNESS AND CONNECTOR (RADIO AND DISPLAY RECEIVER ASSEMBLY - NAVIGATION ECU)
(a) Disconnect the K1 radio and display receiver assembly connector. (b) Dis
