Toyota Camry (XV70): RL Speed Sensor Wrong Installation (X0453)
DESCRIPTION
|
Code | Tester Display |
Measurement Item | Trouble Area |
|---|---|---|---|
|
X0453 | RL Speed Sensor Wrong Installation |
History of rear speed sensor LH being installed incorrectly |
Rear Speed Sensor LH |
PROCEDURE
| 1. |
CHECK FOR DTCs (HEALTH CHECK) |
(a) Perform the Health Check using the Techstream.
| Result |
Proceed to |
|---|---|
| DTCs are not output |
A |
| DTCs are output |
B |
| B |
.gif) | GO TO DIAGNOSTIC TROUBLE CODE CHART |
|
.gif)
| 2. |
CHECK PART NUMBER (REAR SPEED SENSOR LH) |
(a) Check that the rear speed sensor LH is installed.
OK:
Proper rear speed sensor LH is installed.
NOTICE:
If it is necessary to remove components in order to check the rear speed sensor LH, follow the relevant installation and removal procedures and precautions for those components.
HINT:
The rear speed sensor LH (for 2WD) and rear speed sensor rotor LH are incorporated into the rear axle hub and bearing assembly LH.
If the rear speed sensor LH (for 2WD) and rear speed sensor rotor LH need to be replaced, replace the rear axle hub and bearing assembly LH.
| NG | | REPLACE REAR SPEED SENSOR LH for 2WD: Click here for AWD: Click here
|
.gif)
|
| 3. |
CLEAR VEHICLE CONTROL HISTORY (RoB) |
(a) Using the Techstream, clear the Vehicle Control History (RoB).
Chassis > Brake > Utility|
Tester Display |
|---|
| Vehicle Control History (RoB) |
|
| 4. |
CHECK VEHICLE CONTROL HISTORY (RoB) |
(a) Using the Techstream, check for Vehicle Control History (RoB).
Chassis > Brake > Utility|
Tester Display |
|---|
| Vehicle Control History (RoB) |
HINT:
The rear speed sensor LH (for 2WD) and rear speed sensor rotor LH are incorporated into the rear axle hub and bearing assembly LH.
If the rear speed sensor LH (for 2WD) and rear speed sensor rotor LH need to be replaced, replace the rear axle hub and bearing assembly LH.
| Result |
Proceed to |
|---|---|
| X0453 is not output |
A |
| X0453 is output |
B |
| A |
| USE SIMULATION METHOD TO CHECK
|
| B |
| REPLACE REAR SPEED SENSOR LH for 2WD: Click here for AWD: Click here
|
READ NEXT:
RR Speed Sensor Wrong Installation (X0454)
DESCRIPTION
Code Tester Display
Measurement Item Trouble Area
X0454 RR Speed Sensor Wrong Installation
History of rear speed sensor RH being installed incorrectly
Yaw Rate Sensor Wrong Installation (X0456)
DESCRIPTION The airbag sensor assembly has a built-in yaw rate and acceleration sensor and detects the vehicle condition.
Code Tester Display
Measurement Item Trouble Area
X0456
Zero Point Calibration of Steering Angle Sensor Initialization Malfunction (X208A)
DESCRIPTION
Code Tester Display
Measurement Item Trouble Area
X208A Zero Point Calibration of Steering Angle Sensor Initialization Malfunction
History of failure in acqu
SEE MORE:
TRAC does not Operate
DESCRIPTION When TRAC or VSC is operating, the skid control ECU (brake actuator assembly) blinks the slip indicator light to inform the driver that slippage occurred.
When in VSC off mode, or TRAC and VSC are disabled, the multi-information display in the combination meter assembly displays "Tract
Reassembly
REASSEMBLY CAUTION / NOTICE / HINT
HINT: Perform the removal and installation of the front disc brake piston, cylinder boot and piston seal one side at a time. PROCEDURE
1. TEMPORARILY TIGHTEN FRONT DISC BRAKE BLEEDER PLUG (a) Temporarily install the front disc brake bleeder plug to the front di
