Toyota Camry owners & service manuals

Toyota Camry (XV70): Ultrasonic Sensor (Front Right Center) Component Internal Failure (C1AE396)

Toyota Camry Repair Manual XV70 (2018-2024) / Audio, Visual, Telematics / Park Assist / Monitoring / Intuitive Parking Assist System / Ultrasonic Sensor (Front Right Center) Component Internal Failure (C1AE396)

DESCRIPTION

The front center ultrasonic sensor RH is installed on the front bumper. The clearance warning ECU assembly detects obstacles based on signals it receives from the front center ultrasonic sensor RH. If an open circuit or other malfunction occurs in the front center ultrasonic sensor RH, the front center ultrasonic sensor RH does not operate correctly.

DTC No.

Detection Item

DTC Detection Condition

Trouble Area

C1AE396

Ultrasonic Sensor (Front Right Center) Component Internal Failure

Front center ultrasonic sensor RH failure

  • Front center ultrasonic sensor RH
  • Clearance warning ECU assembly

CAUTION / NOTICE / HINT

NOTICE:

  • Perform registration after replacing or removing and installing the ultrasonic sensor or clearance warning ECU assembly.

    Click here

  • If a DTC is detected again after the repair, turn the ignition switch to ON and turn the intuitive parking assist system ON, and then clear the DTC.

    Click here

PROCEDURE

1.

CHECK FOR DTC

(a) According to the display on the GTS, check for DTCs.

Body Electrical > Clearance Warning > Trouble Codes

(b) According to the display on the GTS, clear the DTCs.

Body Electrical > Clearance Warning > Clear DTCs

(c) Recheck for DTCs.

Body Electrical > Clearance Warning > Trouble Codes

Result

Proceed to

No DTC is output

A

"C1AE396" is output

B

"C1AE396" and "C1AE387" are output

C

A

USE SIMULATION METHOD TO CHECK

C

GO TO OTHER FLOWCHART (C1AE387)

B

2.

REPLACE FRONT CENTER ULTRASONIC SENSOR RH

(a) Replace the front center ultrasonic sensor RH with a new or normally functioning one.

Click here

HINT:

To check if the ultrasonic sensor is functioning correctly, replace it with another ultrasonic sensor.

NEXT

3.

CHECK FOR DTC

(a) According to the display on the GTS, check for DTCs.

Body Electrical > Clearance Warning > Trouble Codes

(b) According to the display on the GTS, clear the DTCs.

Body Electrical > Clearance Warning > Clear DTCs

(c) Recheck for DTCs.

Body Electrical > Clearance Warning > Trouble Codes

Result

Proceed to

No DTC is output

A

"C1AE396" is output

B

A

END (FRONT CENTER ULTRASONIC SENSOR RH WAS DEFECTIVE)

B

REPLACE CLEARANCE WARNING ECU ASSEMBLY

    READ NEXT:

     Ultrasonic Sensor (Front Right Corner) Missing Message (C1AE487)

    DESCRIPTION This DTC is stored when an open circuit or short occurs in the communication line between the front corner ultrasonic sensor RH and the clearance warning ECU, or when a malfunction occurs

     Brake

     Brake (front)

    SEE MORE:

     Terminals Of Ecu

    TERMINALS OF ECU CLEARANCE WARNING ECU ASSEMBLY (a) Disconnect the R39 clearance warning ECU assembly connector. (b) Measure the voltage and resistance on the wire harness side connector according to the value(s) in the table below. Terminal No. (Symbol) Terminal Description Condit

     Brake Switch "A" Circuit Short to Ground (P057111)

    DESCRIPTION The skid control ECU (brake actuator assembly) receives stop light switch assembly signals and uses them to determine whether or not the brakes are applied. When the brake pedal is depressed and no signal is received from the stop light switch assembly, this DTC is output. DTC No

    © 2023-2025 Copyright www.tocamry.com