Toyota Camry owners & service manuals

Toyota Camry (XV70): USB Device Malfunction (B1585)

Toyota Camry Repair Manual XV70 (2018-2024) / Audio, Visual, Telematics / Navigation / Multi Info Display / Navigation System / USB Device Malfunction (B1585)

DESCRIPTION

This DTC is stored when a malfunction occurs in a connected device.

DTC No.

Detection Item

DTC Detection Condition

Trouble Area

B1585

USB Device Malfunction

When any of the following conditions is met:

  • A non mass-storage class or incompatible protocol USB device connected
  • USB device with an incompatible file system, corrupted or incompatible File Allocation Table (FAT) connected
  • "iPod" malfunction
  • "iPod" with unsupported firmware connected
  • Unsupported "iPod" model connected
  • USB device or "iPod"
  • Radio and display receiver assembly

CAUTION / NOTICE / HINT

NOTICE:

  • Depending on the parts that are replaced during vehicle inspection or maintenance, performing initialization, registration or calibration may be needed. Refer to Precaution for Navigation System.

    Click here

  • When replacing the radio and display receiver assembly, always replace it with a new one. If a radio and display receiver assembly which was installed to another vehicle is used, the following may occur:
    • A communication malfunction DTC may be stored.
    • The radio and display receiver assembly may not operate normally.

PROCEDURE

1.

REPLACE USB DEVICE OR "iPod"

(a) Disconnect the USB device or "iPod" from the No. 1 stereo jack adapter assembly.

(b) Turn the engine switch off.

HINT:

When this DTC has been stored, it is necessary to turn the engine switch off to make it possible for the vehicle to recognize a new device when it is connected.

(c) Turn the engine switch on (ACC).

(d) Connect a known good USB device or "iPod" to the No. 1 stereo jack adapter assembly.

HINT:

  • If the malfunction occurred when a USB device was in use, use another USB device for the inspection. If the malfunction occurred when an "iPod" was in use, use another "iPod" for the inspection.
  • Refer to System Description for compatible formats and versions.

    Click here

NEXT

2.

CHECK DTC

(a) Clear the DTCs.

Body Electrical > Navigation System > Clear DTCs

(b) Recheck for DTCs and check that no DTCs are output.

Body Electrical > Navigation System > Trouble Codes

OK:

No DTCs are output.

OK

END (USB DEVICE FORMAT WAS INCOMPATIBLE, "iPod" VERSION WAS INCOMPATIBLE, OR USB DEVICE OR "iPod" WAS DEFECTIVE)
NG

REPLACE RADIO AND DISPLAY RECEIVER ASSEMBLY

    READ NEXT:

     AV Signal Stoppage (Low Battery Voltage) (B158F)

    DESCRIPTION This DTC is stored when a video or audio signal is interrupted due to battery voltage input to the radio and display receiver assembly dropping temporarily. DTC No. Detection Item

     Stereo Component Amplifier Malfunction (B15A3)

    DESCRIPTION This DTC is stored when a malfunction occurs in the stereo component amplifier assembly. DTC No. Detection Item DTC Detection Condition Trouble Area B15A3 Stereo C

     Navigation Processor Malfunction (B15AD)

    DESCRIPTION These DTCs are stored when a malfunction occurs in the navigation ECU. DTC No. Detection Item DTC Detection Condition Trouble Area B15AD Navigation Processor Malfu

    SEE MORE:

     Brake Pressure Control Solenoid "A" Control Circuit Short to Battery (C13C012,...,C13C949)

    DESCRIPTION The ABS solenoid relay and master cylinder cut solenoid valves are built into the brake actuator assembly. Depending on the operating conditions, the master cylinder cut solenoid valves regulate the brake fluid pressure generated by the pump motor. When this DTC is stored, the fail-s

     Inspection

    INSPECTION PROCEDURE 1. INSPECT CONNECTING ROD THRUST CLEARANCE (a) Install the connecting rod cap. Click here (b) Using a dial indicator, measure the thrust clearance while moving the connecting rod back and forth. Standard Thrust Clearance: 0.15 to 0.40 mm (0.00591 to 0.0157 in.)

    © 2023-2025 Copyright www.tocamry.com