Toyota Camry (XV70): Check For Intermittent Problems
CHECK FOR INTERMITTENT PROBLEMS
CHECK FOR INTERMITTENT PROBLEMS
HINT:
A momentary interruption (open circuit) in the connectors and/or wire harness between the sensors and ECUs can be detected using the Data List function of the Techstream.
(a) Turn the ignition switch off.
(b) Connect the Techstream to the DLC3.
(c) Turn the ignition switch to ON.
(d) Turn the Techstream on.
(e) Enter the following menus: Chassis / Brake / Data List.
(f) Check the data related to power supply fluctuations.
HINT:
A momentary interruption (open circuit) cannot be detected for 3 seconds after the ignition switch is turned to ON (initial check).
Chassis > Brake > Data List|
Tester Display | Measurement Item |
Range | Normal Condition |
Diagnostic Note |
|---|---|---|---|---|
|
EFI Communication Open |
EFI communication open detection |
Normal / Under intermittent |
Normal: Normal Under intermittent: Momentary interruption |
Related DTC: U010087 |
|
Yaw Rate Open | Yaw rate sensor (airbag sensor assembly) open detection |
Normal / Under intermittent |
Normal: Normal Under intermittent: Momentary interruption |
Related DTC: U012587 |
|
Deceleration Open | Acceleration sensor (airbag sensor assembly) open detection |
Normal / Under intermittent |
Normal: Normal Under intermittent: Momentary interruption |
Related DTC: U012587 |
|
Steering Open | Steering angle sensor open detection |
Normal / Under intermittent |
Normal: Normal Under intermittent: Momentary interruption |
Related DTC: U012687 |
(g) Push the line graph button to display the line graph.
(h) Check for intermittent shorts, etc.
OK:
Normal is displayed.
HINT:
If "Under intermittent" remains displayed on the Techstream, measure the resistance between the skid control ECU (brake actuator assembly) and the each sensor or ECM.
(i) While observing the screen, gently jiggle the connector or wire harness between the ECU and each sensors, or between ECUs.
OK:
Normal is displayed.
HINT:
- If a momentary interruption occurs and Under intermittent is displayed on the Techstream, Under intermittent will remain displayed on the Techstream for 1 second after the circuit returns to normal.
.png)
- If the display changes, this indicates that there has been a momentary interruption (open circuit) in the connector and/or wire harness. In this case, repair or replace the connectors and/or wire harnesses as one of them is faulty.
READ NEXT:
Calibration
CALIBRATION DESCRIPTION (a) Refer to the table below and then perform the necessary operation according to the part to be replaced in order to perform calibration.
Parts to be Replaced / Operati
Test Mode Procedure
TEST MODE PROCEDURE SENSOR CHECK USING DEALER MODE (SIGNAL CHECK)
NOTICE:
After replacing or removing and installing a speed sensor, perform Dealer Mode (Signal Check) inspection to confirm that
Problem Symptoms Table
PROBLEM SYMPTOMS TABLE If DTCs are not output but the malfunction persists, use the following table to determine which circuits to inspect for each problem symptom.
HINT: Refer to each inspection pr
SEE MORE:
For safe driving
For safe driving, adjust the seat and mirror to an appropriate
position before driving.
Correct driving posture
Adjust the angle of the seatback
so that you are sitting
straight up and so that you do
not have to lean forward to
steer.
Adjust the seat so that you can
depress the ped
General Information
GENERAL INFORMATION GENERAL DESCRIPTION (a) This manual is written in accordance with SAE J2008.
(b) Repair operations can be separated mainly into the following 3 processes:
(1) Diagnosis (2) Removing/Installing, Replacing, Disassembling/Reassembling, Checking and Adjusting
(3) Final Inspecti
