Toyota Camry (XV70): Dcm Operation History
DCM OPERATION HISTORY
DCM OPERATION HISTORY
HINT:
- This function shows the telematics network status when the DCM (telematics transceiver) was operated. Use this when no DTC is present but this telematics system was unable to connect to the call center. This symptom may occur if cell phone signal strength is very weak.
- This function is used to display operation history information and the time at which it was stored in the DCM (telematics transceiver).
(a) Connect the Techstream to the DLC3.
(b) Turn the engine switch on (IG).
(c) Turn the Techstream on.
(d) Choose "Telematics" from the System Selection Menu, and then click "Utility".
(e) Click "DCM Operation History" on the Utility Selection Menu.
Body Electrical > Telematics > Utility|
Tester Display |
|---|
| DCM Operation History |
(f) Choose "Items" on the DCM Operation History Menu.
HINT:
- When "Operation Code" is recorded, DCM Operation History is displayed on the Techstream.
- The displayed "Function" differs depending on the selected "Items".
(g) Refer to the following chart and check the system operation status displayed on the Techstream. (The following chart is an example of the system operation status.)
System Operation Status Example|
Occurrence time (*1) | Operation Code (*2) |
Function (*3) | Content (*4) |
Roaming (*5) | Voice Call (*6) |
Service Area (*7) | Electric Level (*8) |
|---|---|---|---|---|---|---|---|
|
2017/12/31 12:40:50 | 0101 |
GNSS (Satellite) | Unreceived GNSS (Satellite) signal |
ON | With |
Out of Service | Level 0 |
|
Tester Display |
Description | Range | ||
|---|---|---|---|---|
|
*1 | Occurrence time |
Indicates date of the DCM (telematics transceiver) operation. |
- | |
| *2 |
Operation Code |
Indicates the Operation Code. |
- | |
|
*3 | Function |
Items | Indicates the function name. |
- |
| Common |
| |||
| Emergency Call |
| |||
| *4 |
Content | Indicates the content. |
- | |
| *5 |
Roaming | Indicates whether roaming was used for the communication network. |
ON or OFF | |
|
*6 | Voice Call |
Indicates whether there was a voice call. |
With or Without | |
|
*7 | Service Area |
Indicates whether the vehicle was in the service area. |
Out of Service, Within Range, OFF the Air or Start up (LTE) | |
|
*8 | Electric Level |
Indicates the strength of the cellular signal received by the vehicle. |
Level 0, Level 1, Level2, Level3, Level 4, Level 5 | |
READ NEXT:
Dcm Activation
DCM ACTIVATION HINT: If the DCM (telematics transceiver) has been replaced, it is necessary to perform the Register Vehicle Information procedure.
DCM ACTIVATION (a) Connect the Techstream to the DL
Acn Call End
ACN CALL END ACN CALL END This function terminates the ACN (Automatic Collision Notification) to the telematics provider. After a collision in which the DCM receives "Collision Detection Signal", the
Customize Parameters
CUSTOMIZE PARAMETERS CUSTOMIZE TELEMATICS SYSTEM
(a) Customizing with the Techstream.
NOTICE:
When the customer requests a change in a function, first make sure that the function can be custom
SEE MORE:
Regulations on the use of tire chains
Regulations regarding the use of tire chains vary depending on location
and type of road. Always check local regulations before installing
chains.
■Tire chain installation
Observe the following precautions when installing and removing chains:
Install and remove tire chains in a safe locati
Using the key
Using the key (vehicles without a smart key system)
Releasing
To release the key, press the button.
Folding
To stow the key, press the button
then fold the key.
Using the mechanical key (vehicles with a smart key system)
To take out the mechanical key,
slide the release lever and
