Toyota Camry owners & service manuals

Toyota Camry (XV70): Destination Information Undefined (C1AB8)

Toyota Camry Repair Manual XV70 (2018-2024) / Audio, Visual, Telematics / Park Assist / Monitoring / Blind Spot Monitor System / Destination Information Undefined (C1AB8)

DESCRIPTION

This DTC is stored when correct destination information is not sent from the main body ECU (multiplex network body ECU) and destination information cannot be confirmed after a blind spot monitor sensor has been replaced.

Blind Spot Monitor Master

DTC No.

Detection Item

DTC Detection Condition

Trouble Area

C1AB8

Destination Information Undefined

The blind spot monitor sensor cannot communicate with the main body ECU
  • CAN communication system
  • Main body ECU (multiplex network body ECU)
  • Blind spot monitor sensor RH
Blind Spot Monitor Slave

DTC No.

Detection Item

DTC Detection Condition

Trouble Area

C1AB8

Destination Information Undefined

The blind spot monitor sensor cannot communicate with the main body ECU
  • CAN communication system
  • Main body ECU (multiplex network body ECU)
  • Blind spot monitor sensor LH

CAUTION / NOTICE / HINT

NOTICE:

  • When checking for DTCs, make sure that the blind spot monitor system is turned on.
  • Before replacing the main body ECU (multiplex network body ECU), refer to Registration.

    w/ Smart Key System: Click here

PROCEDURE

1.

CHECK DTC

(a) Check for CAN communication system DTCs.

Click here

OK:

CAN communication system DTCs are not output.

NG

GO TO CAN COMMUNICATION SYSTEM

OK

2.

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

(a) Replace the main body ECU (multiplex network body ECU) with a new or known good one.

Click here

NEXT

3.

RECHECK DTC

(a) Recheck for DTCs and check if the same DTC is output again.

Body Electrical > Blind Spot Monitor Master > Trouble Codes Body Electrical > Blind Spot Monitor Slave > Trouble Codes

Result

Proceed to

No DTCs are output

A

DTC C1AB8 is output ("Blind Spot Monitor Master")

B

DTC C1AB8 is output ("Blind Spot Monitor Slave")

C
A

END
B

REPLACE BLIND SPOT MONITOR SENSOR RH

C

REPLACE BLIND SPOT MONITOR SENSOR LH

    READ NEXT:

     Blind Spot Monitor Master Module Beam Axis Inspection Incomplete (C1ABB)

    DESCRIPTION This DTC is stored when a beam axis inspection has not been performed for the blind spot monitor sensor RH. HINT: This DTC is always stored after replacing a blind spot monitor sensor. T

     Blind Spot Monitor Slave Module Beam Axis Inspection Incomplete (C1ABC)

    DESCRIPTION This DTC is stored when a beam axis inspection has not been performed for the blind spot monitor sensor LH. HINT: This DTC is always stored after replacing a blind spot monitor sensor. T

     Short to GND or Open in Buzzer (C1ABE)

    DESCRIPTION DTC C1ABE is stored when the blind spot monitor sensor LH detects a short to ground or open in the RCTA buzzer (blind spot monitor buzzer) circuit. DTC No. Detection Item

    SEE MORE:

     Front Side Marker Light Bulb

    ComponentsCOMPONENTS ILLUSTRATION *1 FRONT SIDE MARKER LIGHT BULB - - RemovalREMOVAL CAUTION / NOTICE / HINT HINT: Use the same procedure for the RH side and LH side. The following procedure is for the LH side. PROCEDURE 1. REMOVE FRONT SIDE MARKER LIGHT BULB (

     Green Indicator Remains Off

    DESCRIPTION After engine switch on (IG), the DCM (telematics transceiver) will enter into self check mode. The manual (SOS) switch red indicator will illuminate for 2 seconds and turn off followed by the manual (SOS) switch green indicator illuminating and remaining on under normal operation. If nei

    © 2023-2025 Copyright www.tocamry.com