Toyota Camry (XV70): Lost Communication with Meter (B1324,B1325)
DESCRIPTION
These DTCs are stored when communication between the radio and display receiver assembly and combination meter assembly or headup display (meter mirror sub-assembly)* is not possible.
|
DTC No. | Detection Item |
DTC Detection Condition | Trouble Area |
|---|---|---|---|
|
B1324 | Lost Communication with Meter |
CAN reception error |
|
| B1325 |
Lost Communication with HUD |
CAN reception error |
|
- *: w/ Headup Display System
HINT:
The radio and display receiver assembly is the master unit.
WIRING DIAGRAM
CAUTION / NOTICE / HINT
NOTICE:
- Depending on the parts that are replaced during vehicle inspection or maintenance, performing initialization, registration or calibration may be needed. Refer to Precaution for Audio and Visual System.
- When replacing the radio and display receiver assembly, always replace it with a new one. If a radio and display receiver assembly which was installed to another vehicle is used, the following may occur:
- A communication malfunction DTC may be stored.
- The radio and display receiver assembly may not operate normally.
- Inspect the fuses for circuits related to this system before performing the following procedure.
PROCEDURE
|
1. | CHECK DTC |
(a) Check for DTCs and check that no DTCs are output.
Body Electrical > Navigation System > Trouble Codes|
Result | Proceed to |
|---|---|
|
DTC B1324 and B1325 are not output |
A |
| DTC B1324 and B1325 are output |
B |
| DTC B1324 is output |
C |
| DTC B1325 is output |
D |
| A |
.gif) | USE SIMULATION METHOD TO CHECK
|
.gif)
| C |
| GO TO STEP 11 |
| D |
| GO TO STEP 16 |
|
.gif)
| 2. |
CHECK LOCAL BUS |
(a) Disconnect the cable from the negative (-) battery terminal.
(b) Measure the resistance according to the value(s) in the table below.
Standard Resistance:
|
Tester Connection | Condition |
Specified Condition |
|---|---|---|
|
K125-9 - K125-20 | Cable disconnected from negative (-) battery terminal |
54 to 69 Ω |
|
Result | Proceed to |
|---|---|
|
OK | A |
|
NG (Below 54 Ω) | B |
|
NG (70 Ω or higher) | C |
| A |
| USE SIMULATION METHOD TO CHECK
|
| C |
| GO TO STEP 9 |
|
| 3. |
CHECK HARNESS AND CONNECTOR (RADIO AND DISPLAY RECEIVER ASSEMBLY - NO. 17 JUNCTION CONNECTOR) |
(a) Disconnect the cable from the negative (-) battery terminal.
(b) Disconnect the K125 No. 17 junction connector.
(c) Measure the resistance according to the value(s) in the table below.
Standard Resistance:
|
Tester Connection | Condition |
Specified Condition |
|---|---|---|
|
K125-9 - K125-20 | Cable disconnected from negative (-) battery terminal |
108 to 132 Ω |
| NG | | GO TO STEP 8 |
|
| 4. |
CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - NO. 17 JUNCTION CONNECTOR) |
(a) Disconnect the cable from the negative (-) battery terminal.
(b) Disconnect the K125 No. 17 junction connector.
(c) Measure the resistance according to the value(s) in the table below.
Standard Resistance:
|
Tester Connection | Condition |
Specified Condition |
|---|---|---|
|
K125-10 - K125-21 | Cable disconnected from negative (-) battery terminal |
108 to 132 Ω |
| NG | | GO TO STEP 7 |
|
| 5. |
CHECK HARNESS AND CONNECTOR (HEADUP DISPLAY (METER MIRROR SUB-ASSEMBLY) - NO. 17 JUNCTION CONNECTOR) |
(a) Disconnect the cable from the negative (-) battery terminal.
(b) Disconnect the K125 No. 17 junction connector.
(c) Measure the resistance according to the value(s) in the table below.
Standard Resistance:
|
Tester Connection | Condition |
Specified Condition |
|---|---|---|
|
K125-11 - K125-22 | Cable disconnected from negative (-) battery terminal |
200 Ω or higher |
| OK | | REPLACE NO. 17 JUNCTION CONNECTOR |
|
| 6. |
CHECK HARNESS AND CONNECTOR (HEADUP DISPLAY (METER MIRROR SUB-ASSEMBLY) - NO. 17 JUNCTION CONNECTOR) |
(a) Disconnect the cable from the negative (-) battery terminal.
(b) Disconnect the p1 headup display (meter mirror sub-assembly) connector.
(c) Connect the K125 No. 17 junction connector.
(d) Measure the resistance according to the value(s) in the table below.
Standard Resistance:
|
Tester Connection | Condition |
Specified Condition |
|---|---|---|
|
p1-14 (TX+) - p1-15 (TX-) |
Cable disconnected from negative (-) battery terminal |
54 to 69 Ω |
| OK | | REPLACE HEADUP DISPLAY (METER MIRROR SUB-ASSEMBLY)
|
| NG | | REPAIR OR REPLACE HARNESS OR CONNECTOR |
| 7. |
CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - NO. 17 JUNCTION CONNECTOR) |
(a) Disconnect the cable from the negative (-) battery terminal.
(b) Disconnect the K21 combination meter assembly connector.
(c) Connect the K125 No. 17 junction connector.
(d) Measure the resistance according to the value(s) in the table below.
Standard Resistance:
|
Tester Connection | Condition |
Specified Condition |
|---|---|---|
|
K21-36 (TX+) - K21-37 (TX-) |
Cable disconnected from negative (-) battery terminal |
108 to 132 Ω |
| OK | | REPLACE COMBINATION METER ASSEMBLY |
| NG | | REPAIR OR REPLACE HARNESS OR CONNECTOR |
| 8. |
CHECK HARNESS AND CONNECTOR (RADIO AND DISPLAY RECEIVER ASSEMBLY - NO. 17 JUNCTION CONNECTOR) |
(a) Disconnect the cable from the negative (-) battery terminal.
(b) Disconnect the K2 radio and display receiver assembly connector.
(c) Connect the K125 No. 17 junction connector.
(d) Measure the resistance according to the value(s) in the table below.
Standard Resistance:
|
Tester Connection | Condition |
Specified Condition |
|---|---|---|
|
K2-5 (CNH1) - K2-6 (CNL1) |
Cable disconnected from negative (-) battery terminal |
108 to 132 Ω |
| OK | | REPLACE RADIO AND DISPLAY RECEIVER ASSEMBLY
|
| NG | | REPAIR OR REPLACE HARNESS OR CONNECTOR |
| 9. |
CHECK HARNESS AND CONNECTOR (RADIO AND DISPLAY RECEIVER ASSEMBLY - NO. 17 JUNCTION CONNECTOR) |
(a) Disconnect the cable from the negative (-) battery terminal.
(b) Disconnect the K2 radio and display receiver assembly connector.
(c) Measure the resistance according to the value(s) in the table below.
Standard Resistance:
|
Tester Connection | Condition |
Specified Condition |
|---|---|---|
|
K2-5 (CNH1) - K2-6 (CNL1) |
Cable disconnected from negative (-) battery terminal |
108 to 132 Ω |
| OK | | REPLACE RADIO AND DISPLAY RECEIVER ASSEMBLY
|
|
| 10. |
CHECK HARNESS AND CONNECTOR (RADIO AND DISPLAY RECEIVER ASSEMBLY - NO. 17 JUNCTION CONNECTOR) |
(a) Disconnect the cable from the negative (-) battery terminal.
(b) Disconnect the K125 No. 17 junction connector.
(c) Connect the K2 radio and display receiver assembly connector.
(d) Measure the resistance according to the value(s) in the table below.
Standard Resistance:
|
Tester Connection | Condition |
Specified Condition |
|---|---|---|
|
K125-9 - K125-20 | Cable disconnected from negative (-) battery terminal |
108 to 132 Ω |
| OK | | REPLACE NO. 17 JUNCTION CONNECTOR |
| NG | | REPAIR OR REPLACE HARNESS OR CONNECTOR |
| 11. |
CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY POWER SOURCE) |
(a) Disconnect the K21 combination meter assembly connector.
(b) Measure the resistance according to the value(s) in the table below.
Standard Resistance:
|
Tester Connection | Condition |
Specified Condition |
|---|---|---|
|
K21-21 (ES) - Body ground |
Always | Below 1 Ω |
(c) Measure the voltage according to the value(s) in the table below.
Standard Voltage:
|
Tester Connection | Condition |
Specified Condition |
|---|---|---|
|
K21-40 (B) - Body ground |
Always | 11 to 14 V |
|
K21-39 (IG+) - Body ground |
Ignition switch ON | 11 to 14 V |
| NG | | REPAIR OR REPLACE HARNESS OR CONNECTOR |
|
| 12. |
CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - NO. 17 JUNCTION CONNECTOR) |
(a) Disconnect the cable from the negative (-) battery terminal.
(b) Disconnect the K125 No. 17 junction connector.
(c) Connect the K21 combination meter assembly connector.
(d) Measure the resistance according to the value(s) in the table below.
Standard Resistance:
|
Tester Connection | Condition |
Specified Condition |
|---|---|---|
|
K125-10 - K125-21 | Cable disconnected from negative (-) battery terminal |
108 to 132 Ω |
| NG | | GO TO STEP 15 |
|
| 13. |
CHECK HARNESS AND CONNECTOR (RADIO AND DISPLAY RECEIVER ASSEMBLY - NO. 17 JUNCTION CONNECTOR) |
(a) Disconnect the cable from the negative (-) battery terminal.
(b) Disconnect the K125 No. 17 junction connector.
(c) Measure the resistance according to the value(s) in the table below.
Standard Resistance:
|
Tester Connection | Condition |
Specified Condition |
|---|---|---|
|
K125-9 - K125-20 | Cable disconnected from negative (-) battery terminal |
108 to 132 Ω |
| OK | | REPLACE NO. 17 JUNCTION CONNECTOR |
|
| 14. |
CHECK HARNESS AND CONNECTOR (RADIO AND DISPLAY RECEIVER ASSEMBLY - NO. 17 JUNCTION CONNECTOR) |
(a) Disconnect the cable from the negative (-) battery terminal.
(b) Disconnect the K2 radio and display receiver assembly connector.
(c) Connect the K125 No. 17 junction connector.
(d) Measure the resistance according to the value(s) in the table below.
Standard Resistance:
|
Tester Connection | Condition |
Specified Condition |
|---|---|---|
|
K2-5 (CNH1) - K2-6 (CNL1) |
Cable disconnected from negative (-) battery terminal |
108 to 132 Ω |
| OK | | REPLACE RADIO AND DISPLAY RECEIVER ASSEMBLY
|
| NG | | REPAIR OR REPLACE HARNESS OR CONNECTOR |
| 15. |
CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - NO. 17 JUNCTION CONNECTOR) |
(a) Disconnect the cable from the negative (-) battery terminal.
(b) Disconnect the K21 combination meter assembly connector.
(c) Connect the K125 No. 17 junction connector.
(d) Measure the resistance according to the value(s) in the table below.
Standard Resistance:
|
Tester Connection | Condition |
Specified Condition |
|---|---|---|
|
K21-36 (TX+) - K21-37 (TX-) |
Cable disconnected from negative (-) battery terminal |
108 to 132 Ω |
| OK | | REPLACE COMBINATION METER ASSEMBLY |
| NG | | REPAIR OR REPLACE HARNESS OR CONNECTOR |
| 16. |
CHECK HARNESS AND CONNECTOR (HEADUP DISPLAY (METER MIRROR SUB-ASSEMBLY) POWER SOURCE) |
(a) Disconnect the p1 headup display (meter mirror sub-assembly) connector.
(b) Measure the resistance according to the value(s) in the table below.
Standard Resistance:
|
Tester Connection | Condition |
Specified Condition |
|---|---|---|
|
p1-4 (ES) - Body ground |
Always | Below 1 Ω |
(c) Measure the voltage according to the value(s) in the table below.
Standard Voltage:
|
Tester Connection | Condition |
Specified Condition |
|---|---|---|
|
p1-2 (B) - Body ground |
Always | 11 to 14 V |
|
p1-1 (IG) - Body ground |
Ignition switch ON | 11 to 14 V |
| NG | | REPAIR OR REPLACE HARNESS OR CONNECTOR |
|
| 17. |
CHECK HARNESS AND CONNECTOR (HEADUP DISPLAY (METER MIRROR SUB-ASSEMBLY) - NO. 17 JUNCTION CONNECTOR) |
(a) Disconnect the cable from the negative (-) battery terminal.
(b) Disconnect the K125 No. 17 junction connector.
(c) Connect the p1 headup display (meter mirror sub-assembly) connector.
(d) Measure the resistance according to the value(s) in the table below.
Standard Resistance:
|
Tester Connection | Condition |
Specified Condition |
|---|---|---|
|
K125-11 - K125-22 | Cable disconnected from negative (-) battery terminal |
200 Ω or higher |
| NG | | GO TO STEP 20 |
|
| 18. |
CHECK HARNESS AND CONNECTOR (RADIO AND DISPLAY RECEIVER ASSEMBLY - NO. 17 JUNCTION CONNECTOR) |
(a) Disconnect the cable from the negative (-) battery terminal.
(b) Disconnect the K125 No. 17 junction connector.
(c) Measure the resistance according to the value(s) in the table below.
Standard Resistance:
|
Tester Connection | Condition |
Specified Condition |
|---|---|---|
|
K125-9 - K125-20 | Cable disconnected from negative (-) battery terminal |
108 to 132 Ω |
| OK | | REPLACE NO. 17 JUNCTION CONNECTOR |
|
| 19. |
CHECK HARNESS AND CONNECTOR (RADIO AND DISPLAY RECEIVER ASSEMBLY - NO. 17 JUNCTION CONNECTOR) |
(a) Disconnect the cable from the negative (-) battery terminal.
(b) Disconnect the K2 radio and display receiver assembly connector.
(c) Connect the K125 No. 17 junction connector.
(d) Measure the resistance according to the value(s) in the table below.
Standard Resistance:
|
Tester Connection | Condition |
Specified Condition |
|---|---|---|
|
K2-5 (CNH1) - K2-6 (CNL1) |
Cable disconnected from negative (-) battery terminal |
108 to 132 Ω |
| OK | | REPLACE RADIO AND DISPLAY RECEIVER ASSEMBLY
|
| NG | | REPAIR OR REPLACE HARNESS OR CONNECTOR |
| 20. |
CHECK HARNESS AND CONNECTOR (HEADUP DISPLAY (METER MIRROR SUB-ASSEMBLY) - NO. 17 JUNCTION CONNECTOR) |
(a) Disconnect the cable from the negative (-) battery terminal.
(b) Disconnect the p1 headup display (meter mirror sub-assembly) connector.
(c) Connect the K125 No. 17 junction connector.
(d) Measure the resistance according to the value(s) in the table below.
Standard Resistance:
|
Tester Connection | Condition |
Specified Condition |
|---|---|---|
|
p1-14 (TX+) - p1-15 (TX-) |
Cable disconnected from negative (-) battery terminal |
54 to 69 Ω |
| OK | | REPLACE HEADUP DISPLAY (METER MIRROR SUB-ASSEMBLY)
|
| NG | | REPAIR OR REPLACE HARNESS OR CONNECTOR |
READ NEXT:
HD Radio Tuner Malfunction (B1551,B158D,B15A0,B15B0,B15B3,B15B7,B15BA,B15F9)
DESCRIPTION These DTCs are stored when a malfunction occurs in the radio and display receiver assembly.
DTC No. Detection Item
DTC Detection Condition Trouble Area
B1551 HD Ra
Voice Recognition Microphone Disconnected (B1579)
DESCRIPTION The radio and display receiver assembly, roof console box sub-assembly and telephone microphone assembly are connected to each other using the microphone connection detection signal lines.
USB Device Malfunction (B1585)
DESCRIPTION This DTC is stored when a malfunction occurs in a connected device.
DTC No. Detection Item
DTC Detection Condition Trouble Area
B1585 USB Device Malfunction
SEE MORE:
If the vehicle is
submerged or water
on the road is rising
This vehicle is not designed to be able to drive on roads that are
deeply flooded with water. Do not drive on roads where the
roads may be submerged or the water may be rising. It is dangerous
to remain in the vehicle, if it anticipated that the vehicle
will be flooded or set a drift. Remain cal
Installation
INSTALLATION PROCEDURE 1. INSTALL BRAKE PEDAL PAD
(a) Install the brake pedal pad to the brake pedal support assembly. 2. INSTALL STOP LIGHT SWITCH MOUNTING ADJUSTER
(a) Engage the 2 claws to install the stop light switch mounting adjuster.
3. INSTALL BRAKE PEDAL RETURN SPRING
(a) Instal
